1125943 PHOENIX CONTACT - Technology Bsa

Tecnichal data

Notes	General: The PLC-ATP partition plate must be installed for voltages greater than 250V (L1, L2, L3) between identical terminal blocks on adjacent modules. The PLC-ATP separating plate should be installed for safe isolation between adjacent modules The system installer must ensure the touch protection of the product (at voltages > 25 V AC/60 V DC). The product is a built-in device without protection against direct contact. The PLC-ATP separating plate is required at the start and end of every PLC terminal strip.
Product properties	Product type: Relay Module Product family: PLC-INTERFACE Application: Filter to prevent interference Operating mode: 100% operating factor Mechanical service life: approx. 3x 10⁷ cycles Insulation characteristics Insulation: Basic insulation Insulation characteristics: Air clearances and creepage distances between the power circuits Insulation: Basic insulation Overvoltage category: III Pollution degree: 3
Electrical properties	Maximum power dissipation for nominal condition: 2.3 W Test voltage (Winding/contact): 4 kV_rms (50Hz, 1min., winding/contact) Air clearances and creepage distances between the power circuits Rated insulation voltage: 250 VAC Rated surge voltage: 4 kV (Safe isolation, reinforced insulation, and 6 kV between input circuit and output contact current paths)
Input data	Coil side Nominal input voltage U_N: 230 VAC 220 VDC Input voltage range: 179.4 VAC ... 264.5 VAC (20°C) 171.6 VDC ... 253 VDC (20°C) Mains frequency: 50/60 Hz Drive and function: monostable Drive (polarity): polarized Typical input current at U_N: 8.5 mA (50Hz) 10 mA (60Hz) Typical response time: 7 ms Typical release time: 10 ms Typical release voltage: 60 VAC Coil voltage: 110 VDC Protective circuit: RC element Bridge rectifier Status display: Yellow LED
Output data	Switching Contact switching type: 1changeover contact Type of switch contact: Single contact Contact material: AgNi Maximum switching voltage: 250 V AC/DC Minimum switching voltage: 12 V (10mA) Limiting continuous current: 6 A 10 A (value applies to connections 12. If connections 12 are bridged, the normal value applies.) Maximum inrush current: 30 A (300ms, N/O contact) Min. switching current: 10 mA (12V) Interrupting rating (ohmic load) max.: 144 W (24VDC) 240 W (24VDC, value is valid for connections12. If connections12 are bridged, the normal value applies.) 58 W (48VDC) 48 W (60VDC) 50 W (110VDC) 80 W (220VDC) 1500 VA (250VAC) 2500 W (250VAC, value is valid for connections12. If connections12 are bridged, the normal value applies.) Switching capacity: 2 A (DC13, 24V) 0.2 A (DC13, 250V) 6 A (AC15, 24V) 6 A (AC15, 250V)
Connection data	Connection method: Screw connection Stripping length: 8 mm Screw thread: M3 Conductor cross section rigid: 0.14 mm² ... 2.5 mm² Conductor cross section flexible: 0.14 mm² ... 2.5 mm² 0.2 mm² ... 2.5 mm² (Single ferrule) 2x 0.5 mm² ... 1.5 mm² (TWIN ferrule) Conductor cross section AWG: 26 ... 14 Tightening torque: 0.6 Nm ... 0.8 Nm
Dimensions	Width: 14 mm Height: 80 mm Depth: 94 mm
Environmental and real-life conditions	Ambient conditions Degree of protection (Relay base): IP20 (Relay base) Degree of protection (Relay): RT II (Relay) Degree of protection (Installation location): IP54 (Installation location) Ambient temperature (operation): -40°C ... 55°C Ambient temperature (storage/transport): -40°C ... 85°C Altitude: Ã¢¤ 2000 m
Approvals	CE Certificate: CE-compliant UKCA Certificate: UKCA-compliant Shipbuilding approval Certificate: TAE0000196 Corrosive gas test Identification: ISA-S71.04. G3 Harsh Group EN60068-2-60 DNV GL data Temperature: D Humidity: A Vibration: B/C EMC: B Enclosure: Required protection according to the Rules shall be provided upon installation on board
EMC data	Low Voltage Directive: Conformance with Low Voltage Directive Electromagnetic compatibility: Conformance with EMC directive
Standards and regulations	Air clearances and creepage distances between the power circuits Standards/regulations: IEC 60947-5-1
Mounting	Mounting type: DIN rail mounting Assembly instructions: in rows with zero spacing Mounting position: any

Technical Specs

ECLASS	ECLASS-11.0: 27371601 ECLASS-12.0: 27371601 ECLASS-13.0: 27371601
ETIM	ETIM 9.0: EC001437
UNSPSC	UNSPSC 21.0: 39122300

Description

PLC-INTERFACE for protection against interference currents/voltages on the control side. Consisting of PLC-BSC-230UC/21HC/SO46 basic terminal block with screw connection and plug-in miniature relay with power contact up to 10 A, 1 changeover contact, 230 V AC input voltage

Download

PER SCARICARE I DOCUMENTI E' NECESSARIO EFFETTUARE L'ACCESSO AL SITO

Application_note_00006.pdf

Approvals_00240.pdf

Approvals_01560.pdf

Approvals_01561.pdf

Approvals_01883.pdf

Manufacturer_declaration_03379.pdf

Manufacturer_declaration_03380.pdf

Manufacturer_declaration_03597.pdf

Product_information_00033.pdf

Product_information_00078.pdf

Technical_drawing_09020.pdf