1151587 PHOENIX CONTACT - Technology Bsa

ELR H51-IES-24DC500AC-9-IFS - Hybrid motor starter

Hybrid motor starter; functions: start motor, reverse motor, motor protection, emergency stop, network capable, short-circuit protection; input: 24 VDC; output: 3~, 500 VAC, 9 A; connection method: screw and Push-in connection; connection to the Interface system

Product Code: 1151587

Partner cod.: 1151587

PHOENIX CONTACT

Product properties	Product type: Hybrid motor starters Product family: CONTACTRON Operating mode: 100% operating factor
Electrical properties	Number of phases: 3 Motor starter type: Reversing starter Maximum power dissipation for nominal condition: 12 W Switching frequency: Ã¢¤ 2 Hz (Load-dependent) Maximum power dissipation: 7 W Minimum power dissipation: 0.88 W Coordination type: 1 Supply Rated control circuit supply voltage U_S: 24 VDC Control supply voltage range: 19.2 VDC ... 30 VDC Rated control supply current I_S: 60 mA Protective circuit: Surge protection Reverse polarity protection; Parallel polarity protection diode Insulation characteristics Rated insulation voltage: 550 V Rated surge voltage: 6 kV Overvoltage category: III Degree of pollution: 2 Insulation characteristics between the control input and control supply voltage, and auxiliary circuit to the main circuit: Safe isolation (IEC 60947-1) Isolation characteristics between the control input and control supply voltage to auxiliary circuit: Safe isolation (IEC 60947-1) in the auxiliary circuit Ã¢¤ 300 V AC Safe isolation (EN 50178) in the auxiliary circuit Ã¢¤ 300 V AC Emergency tripping Operate threshold: > 60 A Response time: < 0.5 s
Input data	Control Input name: Enable input Note: The enable input is compatible with signals with blanking (semiconductor output signals with test pulse with max. 3ms duration), unblanking pulses of max. 4ms are tolerated without adversely affecting the safety function. Rated actuating voltage U_C: 24 VDC Triggering voltage range: 19.2 VDC ... 30 VDC Rated actuating current I_C: 7 mA Switching threshold: 9.6 V (Ã¢0Ã¢ signal) 19.2 V (Ã¢1Ã¢ signal) Switching level: < 5 VDC (For EMERGENCY STOP) Typical turn-off time: < 30 ms Protective circuit: Reverse polarity protection
Output data	AC output Rated operating voltage U_e: 500 VAC Operating voltage range: 42 VAC ... 550 VAC Rated operating current I_e: 9 A (AC-51) 7 A (AC-53a) Mains frequency: 50/60 Hz Load current range: 1.5 A ... 9 A (see to derating) Trigger characteristic in acc. with IEC 60947-4-2: Class 10A Cooling time: 20 min. (for auto reset) Leakage current: 0 mA Protective circuit: Surge protection; Varistor
Connection data	Control circuits Connection method: Push-in connection Stripping length: 10 mm Conductor cross section rigid: 0.2 mm² ... 2.5 mm² Conductor cross section flexible: 0.2 mm² ... 2.5 mm² Conductor cross section AWG: 24 ... 14 Load circuit Connection method: Screw connection Stripping length: 8 mm Screw thread: M3 Conductor cross section rigid: 0.2 mm² ... 2.5 mm² Conductor cross section flexible: 0.2 mm² ... 2.5 mm² Conductor cross section AWG: 24 ... 14 Tightening torque: 0.5 Nm ... 0.6 Nm 5 lb_f-in. ... 7 lb_f-in.
Signaling	Status display: Yellow LED Operating voltage display: Green LED Error indication: Red LED
Dimensions	Width: 22.5 mm Height: 160 mm Depth: 114.5 mm
Material specifications	Flammability rating according to UL 94: V0 (Housing)
Environmental and real-life conditions	Ambient conditions Degree of protection: IP20 Ambient temperature (operation): -5°C ... 60°C (observe derating) Ambient temperature (storage/transport): -40°C ... 80°C Altitude: Ã¢¤ 2000 m
Approvals	UKCA Certificate: UKCA-compliant
Standards and regulations	Standards/regulations Standards/regulations: IEC 60947-1 EN60947-4-2 IEC 61508 ISO13849-1
Mounting	Assembly instructions: alignable, for spacing see derating Mounting position: vertical (horizontal DIN rail, motor output below)