1234232 PHOENIX CONTACT - Technology Bsa

NEARFI D ETH B - Inductive coupler

NearFi, base coupler for contactless real-time Ethernet transmission in the centimeter range, 100Mbps, full duplex, M12 connection technology, IP65 type of protection. A remote coupler is required for operation.

Product Code: 1234232

Partner cod.: 1234232

PHOENIX CONTACT

Product properties	Product type: Inductive coupler Application: Ethernet MTTF: 239 Years (SN29500 standard, temperature25°C, operating cycle21%) 155 Years (SN29500 standard, temperature40°C, operating cycle34.25%) 81 Years (SN29500 standard, temperature40°C, operating cycle100%) Insulation characteristics Overvoltage category: II Pollution degree: 1
Electrical properties	Maximum power dissipation for nominal condition: 3.72 W Supply Supply voltage range: 19 VDC ... 30 VDC Typical current consumption: 155 mA (at 24VDC, at 25°C) Inrush current: Ã¢¤ 0.25 A (20ms at 24VDC, without remote coupler) Protective circuit: Transient protection, polarity protection
Connection data	Supply Connection method: M12 connector (A-coded)
Interfaces	Data: Ethernet interface, 100Base-T(X) in accordance with IEEE802.3 Transmission speed: 100 Mbps Connection method: M12 female, D-coded No. of channels: 1 Transmission length: 100 m (shielded twisted pair) Transmission medium: Copper Inductive Switch-on time: < 450 ms (ETH Full Duplex operating mode) Range: min. 0 mm typ. 20 mm (at65°C) typ. 40 mm (at 25°C) Wireless modules that can be connected: 1 (Remote coupler) Wireless Wireless modules that can be connected: 1 (Remote coupler) Frequency: 60 GHz Frequency range: 57 GHz ... 64 GHz (Data transmission) Transmission power: < 10 mW (EIRP)
Dimensions	Dimensional drawing: https://dam-mdc.phoenixcontact.com/rendition/156443151564/d36c7f3f40c2e14cb6c5418cfc6d323f/-S204x204-FJPG Width: 80 mm Height: 86 mm Depth: 39 mm
Material specifications	Material: PBT Die-cast zinc Flammability rating according to UL 94: V0 Impact strength: IK06
Cable/line	Other resistance: Resistant to welding splashes
Environmental and real-life conditions	Ambient conditions Degree of protection: IP65 Impact strength: IK06 Ambient temperature (operation): -20°C ... 65°C (observe derating) Ambient temperature (storage/transport): -40°C ... 85°C Altitude: 2000 m Permissible humidity (operation): 10 % ... 95 % Permissible humidity (storage/transport): 10 % ... 95 % Air pressure (operation): 80 kPa ... 108 kPa (up to 2000m above sea level) Air pressure (storage/transport): 66 kPa ... 108 kPa (up to 3500m above sea level)
Approvals	CE Certificate: CE-compliant Wireless approval, Europe Note: RED 2014/53/EU Wireless approval Japan, MIC Identification: 006-001056 KC approval for South Korea Certificate: R-R-PCK-1234232
EMC data	Electromagnetic compatibility: Conformance with EMC Directive 2014/30/EU Conducted noise emission: EN55032 Class A, industrial applications Electrostatic discharge Standards/regulations: EN61000-4-2 Electrostatic dischargeÃ¢ Contact discharge: ± 4 kV (Test Level 2) Discharge in air: ± 8 kV (Test Level 3) Comments: Criterion B Electromagnetic HF field Standards/regulations: EN61000-4-3 Electromagnetic HF fieldÃ¢ Frequency range: 80 MHz ... 1 GHz (Test Level 3) Field intensity: 10 V/m Comments: Criterion A Fast transients (burst) Standards/regulations: EN61000-4-4 Fast transients (burst)Ã¢ Input: ± 2 kV (Test Level 3 - asymmetrical) Output: ± 2 kV (Test Level 3 - asymmetrical) Signal: ± 2 kV (Test Level 3 - asymmetrical) Comments: Criterion B Surge current load (surge) Standards/regulations: EN61000-4-5 Surge current load (surge)Ã¢ Input: ± 0.5 kV (Test Level 1 - symmetrical) ± 1 kV (Test Level 2 - asymmetrical) Output: ± 1 kV (Test Level 2 - asymmetrical) Signal: ± 1 kV (Test Level 2 - asymmetrical) Comments: Criterion B Conducted interference Standards/regulations: EN61000-4-6 Conducted interferenceÃ¢ Frequency range: 0.15 MHz ... 80 MHz (Test Level 3 - asymmetrical) Comments: Criterion A Voltage: 10 V (80%amplitude modulation with 1kHz) Emitted interference Standards/regulations: EN55016-2-3 Comments: Class A, industrial applications Criteria Criterion A: Normal operating behavior within the specified limits. Criterion B: Temporary impairment to operational behavior that is corrected by the device itself.
Standards and regulations	Free from substances that could impair the application of coating: Yes Other resistance: Resistant to welding splashes Standards/regulations: EN60204-1 (PELV) Standard designation: Protective extra-low voltage
Mounting	Mounting type: Wall mounting Assembly instructions: Observe derating Mounting position: any