Industrial Automation

Mechatronics

Industrial Safety

Panel Components

Sensors and Systems of Vision

Pneumatics

Network Comunications

Automation Cables

Design Software

Access services

Enter your reserved area

Access B2B
Log in to your account

Access services

Enter your reserved area

Access B2B
Log in to your account
Country|
||
PHOENIX CONTACT 1559822
PHOENIX CONTACTNot available

SACCBP-M12FS-4CON-M16/1,0-990 - Device connector, rear mounting

Device connector, rear mounting, CC link, 4-position, PVC, red, similar to RAL3000, Socket, straight, M12, coding: A, on free cable end, Rear mounting, M16 x 1.5, Cable connection, cable length: 1 m, CC-Link, Alternative product in accordance with RoHS II without Exemption6c (Pb<0.1%) item no.: 1240072
Product Code: 1559822
Partner cod.: 1559822
PHOENIX CONTACT


Diminuisci la quantità
Aumenta la quantità
Tecnichal data
Technical Specs
Description
Download
Tecnichal data
NotesGeneral: The electrical and mechanical data specified assume that the connector pair is correctly locked and mounted. If the connector is unlocked and if there is a danger of contamination, the connector must be sealed using a protective cap > IP54. Influences arising from litz wires, cables or PCB assembly must also be taken into consideration.
Safety note
Safety note: WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
• The products are suitable for applications in plant, controller, and electrical device engineering.
• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50V AC, conductive connector housings must be grounded
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the corresponding technical data. You will find information:
o On the product
o On the packing label
o In the supplied documentation
o Online at phoenixcontact.com/products under the product
• Only use tools recommended by PhoenixContact
• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
• Ensure that the protective or functional ground has been properly connected.
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).
MountingMounting type: Rear mounting M16 x 1.5 With flat nut
Assembly instructions: With flat nut
Connection method: Cable connection
Product propertiesProduct type: Circular connectors (device side)
Sensor type: CC link
Number of positions: 4
No. of cable outlets: 1
Shielded: yes
Coding: A
Thread type: M12
Insulation characteristics
Overvoltage category: II
Degree of pollution: 3
Material specificationsFlammability rating according to UL 94: V0
Seal material: FKM
Contact material: CuZn
Contact surface material: Ni/Au
Contact carrier material: PA 6.6
Material for screw connection: Brass, nickel-plated
Outer sheath, material: PVC
Electrical propertiesRated surge voltage: 2.5 kV
Contact resistance: ≤ 3 mΩ
Insulation resistance: ≥ 10 MΩ
Nominal voltage UN: 250 V
Nominal current IN: 4 A (Plug/socket in accordance with IEC 61076-2-101, cable technical data is to be observed)
Transmission medium: Copper
Connection dataConductor connection
Connection method: Cable connection
Contact connection type: Socket
Tightening torque: 2 Nm
3 Nm
Mechanical propertiesMechanical data
Insertion/withdrawal cycles: > 100
ConnectorConnection 1
Head design: Socket
Head cable outlet: straight
Head thread type: M12
Coding: A
Connection 2
Head design: free cable end
Cable/lineCable length: 1 m
CC-Link[990]
Cable weight: 78.8 kg/km
Number of positions: 3
Shielded: yes
Cable type: CC-Link[990]
Conductor structure: 3xAWG20/7 + 1xAWG22/19 (filler litz wire)
Conductor structure signal line: 7x 0.28 mm
AWG signal line: 20
Conductor cross section: 0.5 mm²
External cable diameter: 7.7 mm
Outer sheath, material: PVC
External sheath, color: red
Conductor material: Bare Cu litz wires
Material wire insulation: foamed PE, with high density
Single wire, color: white, yellow, blue
Thickness, insulation: 0.89 mm (Outer cable sheath)
Optical shield covering: 78 %
Max. conductor resistance: 31.2 Ω/km
Wave impedance: 110 Ω
Working capacitance: 61 pF
Nominal voltage, cable: 300 V
Smallest bending radius, fixed installation: 77 mm
Ambient temperature (operation): -30°C ... 60°C (cable, fixed installation)
-5°C ... 60°C (Cable, flexible installation)
Environmental and real-life conditionsAmbient conditions
Degree of protection: IP67 (When plugged in)
IP65 (When plugged in)
IP65/IP67
Ambient temperature (operation): -25°C ... 85°C (Plug / socket)
-40°C ... 85°C (without mechanical actuation)
Technical Specs
ECLASSECLASS-11.0: 27440103
ECLASS-12.0: 27440103
ECLASS-13.0: 27440103
ETIMETIM 9.0: EC003570
UNSPSCUNSPSC 21.0: 39121400
Description
Bus system flush-type socket, CC-Link, 4-pos., M12, shielded, rear/screw mounting with M16 thread, with 1 m bus cable
Download
PER SCARICARE I DOCUMENTI E' NECESSARIO EFFETTUARE L'ACCESSO AL SITO

Approvals_00962.pdf

Approvals_01641.pdf

Design-In_00002.pdf

Manufacturer_declaration_01358.pdf

Manufacturer_declaration_02418.pdf

Manufacturer_declaration_05485.pdf

Manufacturer_declaration_09460.pdf

Package_slip_02241.pdf

Technical_drawing_16310.pdf