Not available 
| Product properties | Product type: Interface module No. of channels: 32 Insulation characteristics Insulation: Safe isolation, reinforced insulation Insulation characteristics: Air clearances and creepage distances, input/output Insulation: Safe isolation, reinforced insulation Overvoltage category: III Pollution degree: 2 Insulation characteristics: Air and creepage distances, output/output Insulation: Basic insulation Overvoltage category: III Pollution degree: 2 |
| Electrical properties | No. of channels: 32 Air clearances and creepage distances, input/output Rated insulation voltage: 300 V Rated surge voltage: 6 kV (1.2/50 üs) Air and creepage distances, output/output Rated insulation voltage: 260 V Rated surge voltage: 4 kV (1.2/50 üs) Supported controller YOKOGAWA CS3000 CentumVP Suitable I/O card: ADV551 ADV561 Supported controller YOKOGAWA STARDOM Suitable I/O card: NFDV551 NFDV561 |
| Input data | Nominal input voltage UN: 24 VDC Input voltage range in reference to UN: 0.8 ... 1.1 Input voltage range: 19.2 VDC ... 26.4 VDC Typical input current at UN: 9 mA (per channel) Protective circuit: Damping diode, polarity protection; Damping diode, polarity protection diode Reverse polarity protection; Polarity protection diode Operating voltage display: Green LED Status display/channel: Yellow LED |
| Output data | Switching Contact switching type: 1 N/O contact Type of switch contact: Single contact Contact material: AgSnO Maximum switching voltage: 230 VAC Limiting continuous current: 2 A (Per channel, plug-in fuse (IEC 6012-3/IV, 2AT); for 100% ED 1A per channel) Maximum inrush current: 8 A (Supply, (V1+, V2+), pluggable fuse (UL 248-14, 250 V, 8AT)) Min. switching current: 100 mA Interrupting rating (ohmic load) max.: 48 W (at 24 V DC) 20 W (at 48 V DC) 18 W (at 60 V DC) 23 W (at 110 V DC) 40 W (at 220 V DC) 500 VA (for 250 V AC) |
| Connection data | Field level Connection method: Spring-cage connection Conductor cross section rigid: 0.2 mm² ... 2.5 mm² Conductor cross section flexible: 0.2 mm² ... 1.5 mm² Conductor cross section AWG: 24 ... 14 Controller level Connection method: Yokogawa KS-compatible Number of connections: 1 Number of positions: 50 Note: Usable system cables: Phoenix Contact YUC50, Yokogawa AKB331 Tightening torque: 0.5 Nm |
| Signaling | Status display present: Yes |
| Dimensions | Dimensional drawing: https://dam-mdc.phoenixcontact.com/rendition/156443151564/192f7863e811f3428a99e8a5acd432d3/-S204x204-FJPG Width: 267 mm Height: 127.5 mm Depth: 56.5 mm |
| Environmental and real-life conditions | Ambient conditions Degree of protection: IP00 Degree of protection (Installation location): ⥠IP54 (Installation location) Ambient temperature (operation): -20°C ... 50°C Ambient temperature (storage/transport): -20°C ... 70°C Altitude: ⤠2000 m |
| Standards and regulations | Air clearances and creepage distances, input/output Standards/regulations: EN61010-2-201 Air and creepage distances, output/output Standards/regulations: EN61010-2-201 |
| Mounting | Mounting type: DIN rail mounting Mounting position: any |
| Notes | General: Observe the maximum switching capacity of the relays used Do not connect adjacent channels to SELV/ PELV and voltages dangerous to the touch. The outputs are not suitable for switching different line conductors. The sum of the switching voltages used for adjacent outputs must not exceed the rated insulation voltage value The necessary requirements for insulation (basic insulation or reinforced insulation) from adjacent modules (in DIN-rail direction) must be realized by applying suitable measures (e.g., partition plates). For proper use, the specifications of the installation directive (see Downloads) must be observed. For applications or use with third-party products, the specifications, and the safety and warning instructions of the respective third-party manufacturer must also be met. |
| ECLASS | ECLASS-11.0: 27141152 ECLASS-12.0: 27141152 ECLASS-13.0: 27141152 |
| ETIM | ETIM 9.0: EC002780 |
| UNSPSC | UNSPSC 21.0: 39121400 |
Description other products
