Available 
| Notes | Utilization restriction CCCex note: Use in potentially explosive areas is not permitted in China. |
| Product properties | Product type: Ethernet extenders MTTF: 711 Years (SN29500 standard, temperature25°C, operating cycle21%) 308 Years (SN29500 standard, temperature40°C, operating cycle34.25%) 125 Years (SN29500 standard, temperature40°C, operating cycle100%) |
| System properties | Functionality Basic functions: Ethernet extenders in accordance with ITU-T G.991.2 |
| Electrical properties | Electrical isolation: VCC // Ethernet // DSL (A) // DSL (B) // FE Maximum power dissipation for nominal condition: 4.32 W Mains type: Permanent line Test voltage data interface/power supply: 500 VAC (In accordance with EN/IEC 60079-7) 1.5 kV AC (50Hz, 1min.) Supply Supply voltage range: 18 VDC ... 30 VDC Nominal supply voltage: 24 VDC ±5% (as an alternative or redundant, via backplane bus contact and system current supply) 5 VDC (configuration only, via mini-USB type B) Typical current consumption: < 180 mA (24VDC) Max. current consumption: ⤠2 A (For operation in a joining station, via the DIN rail connector) Function Status and diagnostic indicators: LEDs: US (supply voltage), ACT/LINK (Ethernet data traffic), ERR (errors) 2x LINK / 2x STAT (DSL data traffic portA and portB), DIAG (diagnostic messages) |
| Output data | Signal Output name: Digital output Number of outputs: 2 Voltage output signal: 18 VDC ... 30 VDC (depending on the operating voltage) Current output signal: ⤠150 mA (Short-circuit-proof) Behavior of outputs: Deactivated for device supply via DIN rail connector |
| Connection data | Supply Connection method: COMBICON plug-in screw terminal block Tightening torque: 0.56 Nm ... 0.79 Nm |
| Interfaces | Signal: Ethernet Basic functions: Ethernet extenders in accordance with ITU-T G.991.2 Data: Ethernet interface, 10/100Base-T(X) in accordance with IEEE 802.3 Serial transmission speed: 10/100 Mbps, auto negotiation Connection method: RJ45 jack, shielded 1 port 10/100Base-T(X), auto negotiation No. of channels: 1 Transmission length: < 100 m (shielded twisted pair) Protocols supported: Protocol-transparent for TCP/IP, IPv4, and IPv6 Data: SHDSL interface according to ITU-T G.991.2.bis Serial transmission speed: 4-wire operation: 64 kbps ... 30 Mbps 2-wire operation: 32 kbps ... 15.3 Mbps Connection method: 2 x 2-pos. COMBICON plug-in screw terminal blocks No. of channels: 2 (2-wire operation) Tightening torque: 0.56 Nm ... 0.79 Nm Transmission length: < 20 km (Depending on data rate and cable cross section) Single conductor/terminal point, rigid: 0.2 mm² ... 2.5 mm² Single-wire/terminal point, flexible: 0.2 mm² ... 2.5 mm² Max. AWG conductor cross section, flexible: 14 Min. AWG conductor cross section, flexible: 24 Single-wire/terminal point, rigid AWG max.: 14 Single-wire/terminal point, rigid AWG min.: 24 Stripping length: 7 mm Data: USB 2.0 Connection method: Mini-USB type B, 5-pos. Transmission length: < 5 m (only for configuration and diagnostics) |
| Dimensions | Width: 35 mm Height: 99 mm Depth: 114.5 mm |
| Material specifications | Material: PA 6.6-FR |
| Environmental and real-life conditions | Ambient conditions Degree of protection: IP20 Ambient temperature (operation): -20°C ... 60°C (Freestanding (40 mm spacing to the right and left), no supply of other modules via the device) -20°C ... 55°C (Mounted in rows with zero spacing and low power dissipation of aligned modules) -20°C ... 50°C (Mounted in rows with zero spacing) -20°C ... 45°C (aligned without spacing and supply of other modules via the device, 1.5A) Ambient temperature (storage/transport): -40°C ... 85°C Altitude: ⤠5000 m (For restrictions, see the manufacturer's declaration for altitude operation) Permissible humidity (operation): 10 % ... 95 % (non-condensing) Permissible humidity (storage/transport): 10 % ... 95 % (non-condensing) |
| Approvals | CE Certificate: CE-compliant ATEX Identification: ï II 3 G Ex ec IIC T4 Gc Certificate: PxCIF11ATEX2313643X Note: Please follow the special installation instructions in the documentation! UKEX Identification: ï II 3 G Ex ec IIC T4 Gc Certificate: PxCIMA22UKEX2313643X UL, USA/Canada Identification: 508 Listed Corrosive gas test Identification: ISA-S71.04-1985 G3 Harsh Group A |
| EMC data | Electromagnetic compatibility: Conformance with EMC Directive 2014/30/EU Electrostatic discharge Standards/regulations: EN61000-4-2 Electrostatic dischargeâ Contact discharge: ± 6 kV Discharge in air: ± 8 kV Indirect discharge: ± 6 kV Comments: Criterion B Electromagnetic HF field Standards/regulations: EN61000-4-3 Electromagnetic HF fieldâ Frequency range: 80 MHz ... 3 GHz Field intensity: 10 V/m Comments: Criterion A Fast transients (burst) Standards/regulations: EN61000-4-4 Fast transients (burst)â Input: ± 2 kV Signal: ± 2 kV Comments: Criterion B Surge current load (surge) Standards/regulations: EN61000-4-5 Surge current load (surge)â Input: ± 0.5 kV (sym./asym.) Output: ± 1 kV (asymmetrical, unshielded) Signal: ± 1 kV (asymmetrical, shielded Ethernet cable) ± 1 kV (asymmetrical: line to ground, unshielded SHDSL cable) Comments: Criterion A Conducted interference Standards/regulations: EN61000-4-6 Conducted interferenceâ Frequency range: 0.15 MHz ... 80 MHz Comments: Criterion A Voltage: 10 V Emitted interference Standards/regulations: EN55011 Comments: Class A, industrial applications Criteria Criterion A: Normal operating behavior within the specified limits. Criterion B: Temporary impairment to operational behavior that is corrected by the device itself. |
| Standards and regulations | Standards/regulations: EN50121-4 |
| Mounting | Mounting type: DIN rail: 35 mm Assembly instructions: The product can be snapped onto all 35 mm DIN rails in accordance with EN60715. |
| ECLASS | ECLASS-11.0: 19170407 ECLASS-12.0: 19170407 ECLASS-13.0: 19170407 |
| ETIM | ETIM 9.0: EC000309 |
| UNSPSC | UNSPSC 21.0: 43223100 |
Description other products
