2702902 PHOENIX CONTACT - Technology Bsa

Product properties	Product type: Safety relays Product family: PSRmini Application: Emergency stop Safety door Light grid Solenoid switch Transponder Relay type: Electromechanical relay with force-guided contacts in accordance with IEC/ENÃ61810-3 Times Typical response time: < 220 ms (automatic start) < 175 ms (manual, monitored start) Typ. starting time with U_s: < 250 ms (when controlled via A1) Typical release time: < 20 ms (on demand via the sensor circuit) < 20 ms (on demand via A1) Restart time: < 1 s (Boot time) Recovery time: < 500 ms
Electrical properties	Maximum power dissipation for nominal condition: 6.45 W (U_SÃ=Ã30ÃV, U_LÃ=Ã30ÃV, I²Ã=Ã72ÃA²) Nominal operating mode: 100% operating factor Air clearances and creepage distances between the power circuits Rated insulation voltage: 320 V Rated surge voltage/insulation: Basic insulation 4 kV between all current paths and housing Safe isolation, reinforced insulation 4ÃkV between input circuit and enabling current path (13/14) and enabling current path (23/24) Supply Designation: L+/L- Nominal voltage for I/O supply: 24 VÃDC -20Ã%Ã/Ã+25Ã% (Provided via the IO-Link interface of the IO-Link master.) Current consumption: typ. 16 mA Protective circuit: Serial protection against polarity reversal; Suppressor diode SupplyÃ¢Ã¢¬Ã¢¹ Designation: A1/A2 Rated control circuit supply voltage U_S: 19.2 VÃDC ... 30 VÃDC 24 VÃDC -20Ã%Ã/Ã+25Ã% (provide external protection) Rated control supply current I_S: typ. 60 mA Power consumption at U_S: typ. 1.44 W Inrush current: typ. 2.5 A (ÃÃ¢tÃ=Ã500ÃÃµs at U_s) Filter time: 1 ms (at A1 in the event of voltage dips at U_s) Protective circuit: Serial protection against polarity reversal; Suppressor diode
Input data	Digital: Sensor circuit S0 (S12, S22) Description of the input: safety-related sensor inputs Number of inputs: 2 Input voltage range "0" signal: 0 VÃDC ... 5 VÃDC (S12) For S22, see note in Ã¢Ã¢¬ÃSignal generator connection versionsÃ¢Ã¢¬ section. Input voltage range "1" signal: 11 VÃDC ... 30 VÃDC Input current range "0" signal: 0 mA ... 2 mA (S12, S22) Inrush current: < 5 mA (typ. with U_S at S12, ÃÃ¢tÃ=Ã150Ãms) < 5 mA (typically with U_S at S22/24ÃV, ÃÃ¢tÃ=Ã500ÃÃµs) > -5 mA (typically with U_S at S22/0ÃV, ÃÃ¢tÃ=Ã500ÃÃµs) Filter time: 1.5 ms (Test pulse width of low test pulses) Test pulse rateÃ=Ã5ÃxÃTest pulse width Deactivate the switch-on pulses for safety applications. Concurrence: Ã¢ÃÃ¾ Max. permissible overall conductor resistance: 150 Ã© Protective circuit: Suppressor diode Current consumption: < 5 mA (Typically with U_S at S12) < 5 mA (typically with U_S at S22/24ÃV) > -5 mA (typically with U_S at S22/0ÃV) Digital: Sensor circuit S1 (S32, S42) Description of the input: safety-related sensor inputs Number of inputs: 2 Input voltage range "0" signal: 0 VÃDC ... 5 VÃDC Input voltage range "1" signal: 11 VÃDC ... 30 VÃDC Input current range "0" signal: 0 mA ... 2 mA Inrush current: < 20 mA (typically with U_S) Filter time: max. 1.5 ms (Test pulse width of low test pulses) Test pulse rateÃ=Ã5ÃxÃTest pulse width Deactivate the switch-on pulses for safety applications. Concurrence: Ã¢ÃÃ¾ Max. permissible overall conductor resistance: 150 Ã© Protective circuit: Suppressor diode Current consumption: < 5 mA (typically with U_S) Digital: Diagnostic input (DGN) Description of the input: non-safety-related Number of inputs: 1 Input voltage range: 0 VÃDC ... 30 VÃDC Protective circuit: Suppressor diode Current consumption: typ. 30 mA Digital: Start circuit (S34) Number of inputs: 1 Input voltage range "1" signal: 19.2 VÃDC ... 30 VÃDC (manual start, autostart: 0ÃV) Inrush current: < 10 mA (typically with U_S, ÃÃ¢tÃ=Ã100Ãms) Max. permissible overall conductor resistance: 150 Ã© Protective circuit: Suppressor diode Current consumption: < 5 mA (typically with U_S at S34/24ÃV) > -5 mA (typically with U_S at S34/0ÃV) IO-Link Designation: IO-Link Transmission speed: 230 kbps (COM3) Cycle Time: 5 ms Process data update: 5 ms Amount of process data: max. 31 Byte (Input data) max. 16 Byte (Output data) Description of the input: IO-Link switching and communication cable Number of inputs: 1 Connection method: Spring-cage connection Connection technology: 3-conductor Number of ports: 1 Port type: Class A
Output data	Relay: Enabling current path (13/14, 23/24) Output description: safety-related N/O contacts 2 NO contacts each in series, without delay, floating Number of outputs: 2 (undelayed) Contact switching type: 2 enabling current paths Contact material: AgSnO₂ Switching voltage: min. 12 V AC/DC max. 250 V AC/DC (Observe the load curve) Switching capacity: min. 60 mW Inrush current: min. 3 mA max. 6 A Switching capacity in accordance with IEC 60947-5-1: 4 A (24ÃV (DC13)) 5 A (250ÃV (AC15)) Limiting continuous current: 6 A Sq. Total current: 72 A² (observe derating) Switching frequency: 0.5 Hz Mechanical service life: 10x 10⁶ cycles Output fuse: 6 A gL/gG 4 A gL/gG (for low-demand applications) Signal: M1 Output description: PNP non-safety-related Number of outputs: 1 Voltage: approx. 22 VÃDC (U_sÃ-Ã2ÃV) Current: max. 100 mA Maximum inrush current: 500 mA (ÃÃ¢tÃ=Ã1Ãms at U_s) Protective circuit: Suppressor diode
Connection data	Connection technology pluggable: yes Conductor connection Connection method: Push-in connection Conductor cross section rigid: 0.2 mm² ... 1.5 mm² Conductor cross section flexible: 0.2 mm² ... 1.5 mm² Conductor cross section, flexible, with ferrule, with plastic sleeve: 0.25 mm² ... 1.5 mm² (only together with CRIMPFOX 6) Conductor cross section flexible, with ferrule without plastic sleeve: 0.25 mm² ... 1.5 mm² (only together with CRIMPFOX 6) Conductor cross-section AWG: 24 ... 16 Stripping length: 8 mm
Signaling	Status display: 5x LED green Operating voltage display: 1 x green, yellow, red LED
Dimensions	Width: 17.5 mm Height: 116.6 mm Depth: 114.5 mm
Material specifications	Housing material: Polyamide
Characteristics	Safety data Stop category: 0 Safety data: ENÃISOÃ13849 Category: 4 Performance level (PL): e (4ÃAÃDC13; 5ÃAÃAC15; 8760Ãswitching cycles/year) Safety data: IEC 61508 - High demand Safety Integrity Level (SIL): 3 Safety data: IEC 61508 - Low demand Safety Integrity Level (SIL): 3 Safety data: ENÃIEC 62061 Safety Integrity Level (SIL): 3
Environmental and real-life conditions	Ambient conditions Degree of protection: IP20 Min. degree of protection of inst. location: IP54 Ambient temperature (operation): -25°C ... 60°C (observe derating) Ambient temperature (storage/transport): -40°C ... 85°C Maximum altitude: Ã¢Ã¢°¤ 2000 m (Above sea level) Max. permissible humidity (storage/transport): 75 % (on average, 85% infrequently, non-condensing) Max. permissible relative humidity (operation): 75 % (on average, 85% infrequently, non-condensing) Shock: 15g Vibration (operation): 10ÃHzÃ...Ã150ÃHz, 2g
Approvals	CE Identification: CE-compliant
Standards and regulations	Air clearances and creepage distances between the power circuits Standards/regulations: DINÃENÃ60947-1
Mounting	Mounting type: DIN rail mounting Assembly instructions: See derating curve Mounting position: vertical or horizontal Connection method: Push-in connection