2897758 PHOENIX CONTACT - Technology Bsa

IL EIP BK DI8 DO4 2TX-PAC - Bus coupler

Inline, Bus coupler, EtherNet/IPâ¢, RJ45 jack, Digital inputs: 8, 24 VDC, connection technology: 3-conductor, Digital outputs:4, 24 VDC, 500 mA, connection technology:3-conductor, transmission speed in the local bus:500 kbps / 2 Mbps, degree of protection: IP20, including Inline connectors and marking fields

Product Code: 2897758

Partner cod.: 2897758

PHOENIX CONTACT

Dimensions	Dimensional drawing: https://dam-mdc.phoenixcontact.com/rendition/156443151564/4466fa705ece7847b56185793696fa26/-S204x204-FJPG Width: 80 mm Height: 119.8 mm Depth: 71.5 mm Note on dimensions: Specfications with connectors
Notes	Utilization restriction CCCex note: Use in potentially explosive areas is not permitted in China.
Interfaces	EtherNet/IPÃ¢¢ Number of interfaces: 2 Connection method: RJ45 jack Note on the connection method: Auto negotiation and autocrossing Permissible conductor cross section: 0.14 mm² ... 0.22 mm² (twisted pair) Transmission speed: 10/100 Mbps (half or full duplex (automatic detection)) Transmission physics: Ethernet in RJ45 twisted pair Inline local bus Number of interfaces: 1 Connection method: Inline data jumper Transmission speed: 500 kbps / 2 Mbps (automatic detection, no combined system) Fieldbus: Local bus gateway Max. number of local bus devices: 61 (The on-board I/Os are two devices)
System properties	System limits Number of supported devices: max. 63 (per station) Number of local bus devices that can be connected: max. 61 (The on-board I/Os are two devices) Number of devices with parameter channel: max. 8 Number of supported branch terminals with remote bus branch: 0 Module ID code (hex): none Input address area: 8 bit Output address area: 4 bit Register length: 16 bit
Input data	Digital Input name: Digital inputs Description of the input: EN 61131-2 type 1 Number of inputs: 8 Connection method: Inline connector Connection technology: 3-conductor Input voltage: 24 VDC Input voltage range "0" signal: -30 VDC ... 5 VDC Input voltage range "1" signal: 15 VDC ... 30 VDC Nominal input voltage U_IN: 24 VDC Nominal input current at U_IN: typ. 3 mA Typical input current per channel: typ. 3 mA Typical response time: approx. 500 µs Delay at signal change from 0 to 1: 1.2 ms Delay at signal change from 1 to 0: 1.2 ms Protective circuit: Reverse polarity protection; Suppressor diode
Output data	Digital Output name: Digital outputs Connection method: Inline connector Connection technology: 3-conductor Number of outputs: 4 Protective circuit: Short-circuit and overload protection; Free running circuit Output voltage: 24 VDC -1V (At nominal current) Maximum output current per module: max. 2 A Nominal output voltage: 24 VDC Output current when switched off: max. 10 µA (When not loaded, a voltage can be measured even at an output that is not set.) Nominal load, inductive: 12 VA (1.2 H, 48 Ã©) Nominal load, lamp: 12 W Nominal load, ohmic: 12 W Reverse voltage resistance to short pulses: Reverse voltage proof Behavior with overload: Auto restart Behavior with inductive overload: Output can be destroyed Behavior at voltage switch-off: The output follows the power supply without delay Signal delay: typ. 1.2 ms Overcurrent shut-down: min. 0.7 A
Product properties	Type: modular Product type: I/O component Product family: Inline Scope of delivery: including Inline connectors and marking fields No. of channels: 12 Diagnostics messages: Short-circuit or overload of the digital outputs yes Sensor supply failure yes Failure of the actuator supply yes
Electrical properties	No. of channels: 12 Maximum power dissipation for nominal condition: 23.5 W Power dissipation: typ. 1.7 W (entire device) Potentials Power consumption: typ. 3 W (entire device) Protective circuit: Short-circuit protection of the communications power; electronic Short-circuit protection of the analog supply; electronic Potentials: Bus coupler supply U Supply voltage: 24 VDC (via Inline connector) Supply voltage range: 19.2 VDC ... 30 VDC (including all tolerances, including ripple) Current draw: max. 0.98 A (with max. number of connected I/O terminal blocks) 80 mA (without connected I/O terminal blocks) Potentials: Communications power (U Supply voltage: 7.5 VDC Potentials: Supply of analog modules (U Supply voltage: 24 VDC Supply voltage range: 19.2 VDC ... 30 VDC (including all tolerances, including ripple) Potentials: Main circuit supply (U Supply voltage: 24 VDC (via Inline connector) Supply voltage range: 19.2 VDC ... 30 VDC (including all tolerances, including ripple) Current draw: max. 8 ADC min. 3 mA (without connected peripherals) Potentials: Segment circuit supply (U Supply voltage: 24 VDC (via Inline connector) Supply voltage range: 19.2 VDC ... 30 VDC (including all tolerances, including ripple) Current draw: max. 8 ADC min. 6 mA (without connected peripherals)
Connection data	Connection technology Connection name: Inline connector Conductor connection Connection method: Spring-cage connection Conductor cross section rigid: 0.08 mm² ... 1.5 mm² Conductor cross section flexible: 0.08 mm² ... 1.5 mm² Conductor cross section AWG: 28 ... 16 Stripping length: 8 mm Inline connector Connection method: Spring-cage connection Conductor cross section, rigid: 0.08 mm² ... 1.5 mm² Conductor cross section, flexible: 0.08 mm² ... 1.5 mm² Conductor cross section AWG: 28 ... 16 Stripping length: 8 mm
Environmental and real-life conditions	Ambient conditions Ambient temperature (operation): -25°C ... 60°C Degree of protection: IP20 Air pressure (operation): 70 kPa ... 106 kPa (up to 3000m above sea level) Air pressure (storage/transport): 70 kPa ... 106 kPa (up to 3000m above sea level) Ambient temperature (storage/transport): -25°C ... 85°C Permissible humidity (operation): 10 % ... 95 % (non-condensing) Permissible humidity (storage/transport): 10 % ... 95 % (non-condensing)
Standards and regulations	Protection class: III (IEC 61140, EN61140, VDE0140-1)
Mounting	Mounting type: DIN rail mounting