2900321 PHOENIX CONTACT - Technology Bsa

Tecnichal data

Product properties	Product type: Relay Module Product family: PLC-INTERFACE Installation location: Attached to the vehicle body Application: Railway applications Operating mode: 100% operating factor Mechanical service life: approx. 2x 10⁷ cycles Insulation characteristics Overvoltage category: III Pollution degree: 2
Electrical properties	Maximum power dissipation for nominal condition: 0.22 W Test voltage (Winding/contact): 4 kV_rms (50Hz, 1min., winding/contact) Rated insulation voltage: 250 VAC Rated surge voltage: 6 kV
Input data	Coil side Nominal input voltage U_N: 24 VDC Input voltage range: 18.5 VDC ... 33.6 VDC Input voltage range in reference to U_N: 0.7 ... 1.25 Drive and function: monostable Drive (polarity): polarized Typical input current at U_N: 9 mA Typical response time: 4 ms Typical release time: 4 ms Coil voltage: 12 VDC Protective circuit: Surge protection; Freewheeling diode RCZ filter Wide-range electronics Operating voltage display: Yellow LED
Output data	Switching Contact switching type: 1changeover contact Type of switch contact: Single contact Contact material: AgSnO, hard gold-plated Maximum switching voltage: 30 VAC 36 VDC Minimum switching voltage: 100 mV (10mA) Limiting continuous current: 50 mA Maximum inrush current: 50 mA Min. switching current: 1 mA (24V) Short-circuit current: 200 A (conditional short-circuit current) Interrupting rating (ohmic load) max.: 1.2 W (at 24 V DC) Output fuse: 4 A gL/gG NEOZED Switching capacity: 1 A (24V (DC13)) 0.2 A (110 V (DC13)) 0.1 A (220 V (DC13)) 3 A (24V (AC15)) 3 A (120V (AC15)) 3 A (230 V (AC 15)) Switching: when the gold layer is destroyed Note: the following values are applicable if a gold layer is destroyed Maximum switching voltage: 250 V AC/DC (Separating plate PLC-ATP must be installed for voltages larger than 250V (L1, L2, L3) between identical terminal blocks in adjacent modules.) Minimum switching voltage: 12 V AC/DC Limiting continuous current: 6 A Min. switching current: 10 mA Interrupting rating (ohmic load) max.: 140 W (at 24 V DC) 20 W (at 48 V DC) 18 W (at 60 V DC) 23 W (at 110 V DC) 40 W (at 220 V DC) 1500 VA (for 250 V AC) Switching capacity: 2 A (at 24 V, DC13) 0.2 A (at 110 V, DC13) 0.1 A (at 220 V, DC13) 3 A (at 24 V, AC15) 3 A (at 120 V, AC15) 3 A (at 230 V, AC15)
Connection data	Connection method: Push-in connection Stripping length: 10 mm Conductor cross section rigid: 0.14 mm² ... 2.5 mm² Conductor cross section flexible: 0.14 mm² ... 2.5 mm² 0.2 mm² ... 2.5 mm² (Single ferrule) 2x 0.5 mm² ... 1 mm² (TWIN ferrule) Conductor cross section AWG: 26 ... 14
Dimensions	Width: 6.2 mm Height: 80 mm Depth: 94 mm
Material specifications	Flammability rating according to UL 94: V0 (Housing)
Environmental and real-life conditions	Ambient conditions Degree of protection (Relay): RT III (Relay) Degree of protection (Relay base): IP20 (Relay base) Ambient temperature (operation): -40°C ... 70°C (Temperature class TX) Ambient temperature (storage/transport): -40°C ... 85°C
Approvals	CE Certificate: CE-compliant UKCA Certificate: UKCA-compliant Shipbuilding approval Certificate: TAE0000196 Corrosive gas test Identification: ISA-S71.04. G3 Harsh Group EN60068-2-60 DNV GL data Temperature: D Humidity: A Vibration: B/C EMC: B Enclosure: Required protection according to the Rules shall be provided upon installation on board
EMC data	Low Voltage Directive: Conformance with Low Voltage Directive Electromagnetic compatibility: Conformance with EMC directive
Standards and regulations	Standards/regulations: IEC 60947-5-1 EN50155 (VDE0115 part 200) EN61373 EN50121
Mounting	Mounting type: DIN rail mounting Assembly instructions: in rows with zero spacing Mounting position: any

Technical Specs

ECLASS	ECLASS-11.0: 27371601 ECLASS-12.0: 27371601 ECLASS-13.0: 27371601
ETIM	ETIM 9.0: EC001437
UNSPSC	UNSPSC 21.0: 39122300

Description

PLC-INTERFACE for railway applications, consisting of basic terminal block with push-in connection and plug-in miniature relay with multi-layer gold contact, range: 0.7 x U_N to 1.25 x U_N, temperature class TX: -40°C to +70°C, 1 PDT, input voltage 24 V DC

Download

PER SCARICARE I DOCUMENTI E' NECESSARIO EFFETTUARE L'ACCESSO AL SITO

Approvals_00240.pdf

Approvals_01560.pdf

Approvals_01561.pdf

Approvals_01883.pdf

Manufacturer_declaration_01841.pdf

Manufacturer_declaration_03375.pdf

Manufacturer_declaration_03376.pdf

Manufacturer_declaration_03596.pdf

Manufacturer_declaration_15504.pdf

Package_slip_01741.pdf

Product_information_00033.pdf

Product_information_00533.pdf

Technical_drawing_39347.pdf