2903908 PHOENIX CONTACT - Technology Bsa

ELR H5-I-PT- 24DC/500AC-0,6 - Hybrid motor starter

Hybrid motor starter for reversing 3~AC motors up to 500VAC and 0.6A output current, with 24VDC control voltage, adjustable overload shutdown, and push-in connection.

Product Code: 2903908

Partner cod.: 2903908

PHOENIX CONTACT

Notes	General: If this device is to be used in combination with the CrossPowerSystem power distribution board, the device mount for the 16 A fuse (order designation: EM-CPS-DA-22,5F/16A; order number: 1002668) is required in order to attach the hybrid motor starter to the power distribution board.
Product properties	Product type: Hybrid motor starters Product family: CONTACTRON Operating mode: 100% operating factor
Electrical properties	Number of phases: 3 Motor starter type: Reversing starter Maximum power dissipation for nominal condition: 0.4 W Switching frequency: Ã¢¤ 2 Hz (Load-dependent) Maximum power dissipation: 1.5 W Minimum power dissipation: 1.1 W Coordination type: 1 Supply Rated control circuit supply voltage U_S: 24 VDC Control supply voltage range: 19.2 VDC ... 30 VDC Rated control supply current I_S: 40 mA Protective circuit: Surge protection Reverse polarity protection Insulation characteristics Rated insulation voltage: 500 V Rated surge voltage: 6 kV Overvoltage category: III Degree of pollution: 2 Insulation characteristics between the control input and control supply voltage, and auxiliary circuit to the main circuit: Safe isolation (IEC 60947-1) at operating voltage Ã¢¤ 300 V AC (e.g., 230/400 V AC, 277/480 V AC) Basic insulation (IEC 60947-1) at operating voltage 300VAC...500VAC Isolation characteristics between the control input and control supply voltage to auxiliary circuit: Safe isolation (IEC 60947-1) in the auxiliary circuit Ã¢¤ 300 V AC
Input data	Control Input name: Control input right/left Rated actuating voltage U_C: 24 VDC Triggering voltage range: 19.2 VDC ... 30 VDC Rated actuating current I_C: 5 mA (Input type 1) Switching threshold: 9.6 V (Ã¢0Ã¢ signal) 19.2 V (Ã¢1Ã¢ signal) Typical turn-off time: < 30 ms Protective circuit: Reverse polarity protection
Output data	AC output Rated operating voltage U_e: 500 VAC Operating voltage range: 42 VAC ... 550 VAC Rated operating current I_e: 0.6 A (AC-51) 0.6 A (AC-53a) Mains frequency: 50/60 Hz Load current range: 75 mA ... 600 mA (see to derating) Trigger characteristic in acc. with IEC 60947-4-2: Class 10A Cooling time: 20 min. (for auto reset) Leakage current: 0 mA Protective circuit: Surge protection Acknowledge output Note: Confirmation: floating change-over contact, signal contact Contact switching type: 1changeover contact Switching capacity in accordance with IEC 60947-5-1: 3 A (230 V, AC15) 2 A (24V, DC13)
Connection data	Control circuits Connection method: Push-in connection Stripping length: 10 mm Conductor cross section rigid: 0.2 mm² ... 2.5 mm² Conductor cross section flexible: 0.2 mm² ... 2.5 mm² Conductor cross section AWG: 24 ... 14 Load circuit Connection method: Push-in connection Stripping length: 10 mm Conductor cross section rigid: 0.2 mm² ... 2.5 mm² Conductor cross section flexible: 0.2 mm² ... 2.5 mm² Conductor cross section AWG: 24 ... 14
Signaling	Status display: Yellow LED Operating voltage display: Green LED Error indication: Red LED
Dimensions	Width: 22.5 mm Height: 107.5 mm Depth: 114 mm
Material specifications	Flammability rating according to UL 94: V0 (Housing)
Environmental and real-life conditions	Ambient conditions Degree of protection: IP20 Ambient temperature (operation): -25°C ... 70°C (observe derating) Ambient temperature (storage/transport): -40°C ... 80°C Altitude: Ã¢¤ 2000 m
Approvals	UKCA Certificate: UKCA-compliant UL approval Certificate: NLDX.E228652 UL data SCCR: 100 kA (500 V AC (fuse: 30 A class CC/30 A class J (high fault))) 5 kA (500 V AC (fuse: 20 A RK5 (standard fault))) FLA: 0.6 A (500 V AC) Group installation: 20 A (class RK5, SCCR 5kA, #24 - 14 AWG max. solid and stranded) 30 A (class CC or J, SCCR 100kA, #24 - 14 AWG max, solid and stranded) Category code: NLDX / NRNT
Standards and regulations	Standards/regulations Standards/regulations: IEC 60947-1 IEC 60947-4-2
Mounting	Mounting type: DIN rail mounting Assembly instructions: alignable, for spacing see derating Mounting position: vertical (horizontal DIN rail, motor output below)