Not available 
| Input data | Input voltage: 24 VDC Input voltage range: 18 VDC ... 30 VDC Electric strength, max.: 35 VDC (Protected against polarity reversal) Internal input fuse: no Typical national grid voltage: 24 VDC Voltage type of supply voltage: DC Inrush current: ⤠7 A (â¤4ms) Reverse polarity protection: yes Fixed backup threshold: 22 VDC 30 VDC Dynamic activation threshold: > 1V / 100ms Switch-on time: max. 3 s Switch-on time during battery operation (Bat.-Start): 8 s Voltage drop, input/output: 0.4 VDC Current consumption IN (UN, IOUT = IN, Icharge = 0): 10.1 A Current consumption Imax (UN, IOUT = IStat.Boost, Icharge = max): 16.2 A Current consumption INo-Load(UN, IOUT = 0, Icharge = 0): 48 mA Current consumption Icharge (UN, IOUT = 0, Icharge = max): 3.5 A Power consumption PN (UN, IOUT = IN, Icharge = 0): 241 W Power consumption Pmax (UN, IOUT = IStat.Boost, Icharge = max): 384 W Power consumption PNo-Load (UN, IOUT = 0, Icharge = 0): 1.2 W Power consumption Pcharge (UN, IOUT = 0, Icharge = max): 90 W Signal state Bat.-Start Connection labeling: 3.8 (+) Channel: DI (digital input) State: Bat.-Mode State condition: Low level (30ms) Low signal: Input connected with SGnd (3.9) orBat High signal: Input not connected or connected with>UBat Signal - state assignment: low - active Reference potential: 3.9 (SGnd, identical to 1.2, 2.2, 4.2) LED status indicator: Yellow (Bat.-Mode) Signal state PS Boost Connection labeling: 3.7 (+) Channel (configurable): DI (digital input) default, AI (analog input) State (configurable): Charging current reduced State condition: Low level Low signal: Input connected with SGnd (3.9), <5VDC or not connected High signal: Input connected with 13 ⦠30VDC Signal - state assignment: low - active Analog: 4 mA ... 20 mA (Offset zero point) Unit signal: I (mA) Load: 390 é Reference potential: 3.9 (SGnd, identical to 1.2, 2.2, 4.2) Signal state Remote Connection labeling: 3.6 (+) Channel: DI (digital input) State (configurable): Disconnection State condition: Low level Low signal: Input connected with SGnd (3.9) or<5VDC High signal: Input not connected or connected with 13 ⦠30VDC Signal - state assignment: low - active Reference potential: 3.9 (SGnd, identical to 1.2, 2.2, 4.2) LED status indicator: Green, flashing (DC OK) |
| Output data | Efficiency: typ. 98 % Number of outputs: 1 Short-circuit-proof: yes No-load proof: yes Switch-over time: 0 ms UPS connection in parallel: no UPS connection in series: no Energy storage device connection in parallel: Yes, 5 (observe line protection) Energy storage device connection in series: no Mains operation Output voltage: 24 VDC (UOUT = UIN - 0.4VDC) Output voltage range: 18 VDC ... 30 VDC (UOUT = UIN - 0.4VDC) 18 VDC ... 32 VDC Output current IN: 10 A Static Boost (IStat.Boost): 12.5 A Dynamic Boost (IDyn.Boost): 20 A (5 s) Selective Fuse Breaking (ISFB): 60 A (15 ms) Output power POUT (UN, IOUT = IN): 240 W Output power POUT (UN, IOUT = Istat.Boost): 300 W Output power POUT (UN, IOUT = Idyn.Boost): 480 W (5 s) Power dissipation No load (UN, IOut = 0, ICharge = 0): 3 W Power dissipation Nominal load (UN, IOut = IN, ICharge = 0): 8 W Battery operation Output voltage: 24 VDC (UOUT = UBAT - 0.4VDC) Output voltage range: 19 VDC ... 28 VDC (UOUT = UBAT - 0.4VDC) Output current IN: 10 A Static Boost (IStat.Boost): 12.5 A Dynamic Boost (IDyn.Boost): 20 A (5 s) Selective Fuse Breaking (ISFB): 60 A (15 ms) Output power POUT (UN, IOUT = IN): 240 W Output power POUT (UN, IOUT = Istat.Boost): 300 W Output power POUT (UN, IOUT = Idyn.Boost): 480 W (5 s) Power dissipation No load (UN, IOut = 0, ICharge = 0): 2 W Power dissipation Nominal load (UN, IOut = IN, ICharge = 0): 8 W Signal supply 24VDC, 20mA, SGnd Connection labeling: 3.1 (+), 3.9 (SGnd) Output voltage: 24 VDC Output can be loaded: max. 20 mA Reference potential: 3.9 (SGnd, identical to 1.2, 2.2, 4.2) Signal state Alarm Connection labeling: 3.2, 3.3 Channel: DO (digital output) Switching voltage: max. 30 V AC/DC Switch contact (floating): OptoMOS State (configurable): Group alarm State condition (configurable): Alarm threshold Current carrying capacity: max. 100 mA State - signal assignment: NC (Normally Closed) LED status indicator: red (Alarm) Signal state Bat. mode Connection labeling: 3.4 (+) Channel: DO (digital output) Semiconductor output: MOSFET State (configurable): Bat.-Mode State condition (configurable): UIN<18VDC, UIN>30VDC, Bat.-Start Output voltage: 19 VDC ... 28 VDC (buffered) Output can be loaded: max. 20 mA State - signal assignment: active - high Reference potential: 3.9 (SGnd, identical to 1.2, 2.2, 4.2) LED status indicator: Yellow (Bat.-Mode) Signal state Ready Connection labeling: 3.5 (+) Channel: DO (digital output) Semiconductor output: MOSFET State (configurable): Ready State condition (configurable): SOC=100% Output voltage: 19 VDC ... 28 VDC (buffered) Output can be loaded: max. 20 mA State - signal assignment: active - high Reference potential: 3.9 (SGnd, identical to 1.2, 2.2, 4.2) LED status indicator: Green (state of charge - SOC) |
| Energy storage | Nominal voltage UN: 24 VDC End-of-charge voltage (temperature-compensated): 25 VDC ... 32 VDC End-of-charge voltage (configurable): 27.6 VDC Charging current (configurable): max. 3 A Nominal capacity (without additional charger): 1.2 Ah ... 80 Ah Max. capacity: 80 Ah Charging time: 160 min. (7.2 Ah) Buffer time: 25 min. (7.2 Ah) Deep discharge protection (configurable): 19.2 VDC Battery technology: VRLA, VRLA-WTR, LI-ION Charge characteristic curve: IU0U IQ-Technology: yes Temperature sensor: yes Temperature compensation (configurable): 42 mV/K |
| Signaling | LED signaling Types of signaling: DC OK (green) Alarm (red) Bat.-Mode (yellow) SOC (red, green) Data (red, green) |
| Product properties | Product type: DC UPS Product family: QUINTUSV MTBF (IEC 61709, SN 29500): > 2065000 h (25°C) > 1184000 h (40°C) > 522600 h (60°C) Environmental protection directive: RoHS Directive 2011/65/EU WEEE Reach Insulation characteristics Protection class: III (without PE) Degree of pollution: 2 Life expectancy (electrolytic capacitors) Time: 137895 h |
| Dimensions | Item dimensions Width: 35 mm Height: 130 mm Depth: 132 mm 125 mm (Device depth (DIN rail mounting)) Item dimensions with alternative mounting Width: 123 mm Height: 130 mm Depth: 37 mm Installation dimensions Installation distance right/left (active): 5 mm / 5 mm (POutâ¥50%) Installation distance right/left (passive): 0 mm / 0 mm (POutâ¥50%) Installation distance right/left (active, passive): 0 mm / 0 mm (POutâ¤50%) Installation distance top/bottom (active): 50 mm / 50 mm (POutâ¥50%) Installation distance top/bottom (passive): 40 mm / 20 mm (POutâ¥50%) Installation distance top/bottom (active, passive): 40 mm / 20 mm (POutâ¤50%) |
| Mounting | Mounting type: DIN rail mounting Mounting position: On horizontal DIN rail NS 35/7.5 and NS 35/15 acc. to EN 60715 |
| Material specifications | Flammability rating according to UL94 (housing / terminal blocks): V0 Housing material: Metal Hood version: Stainless steel X6Cr17 Side element version: Aluminum AlMg3 |
| Environmental and real-life conditions | Ambient conditions Degree of protection: IP20 Ambient temperature (operation): -25°C ... 70°C (>60°C Derating: 2,5%/K) Ambient temperature (storage/transport): -40°C ... 85°C Ambient temperature (start-up type tested): -40°C Maximum altitude: ⤠4000 m Climatic class: 3K3 (EN60721) Max. permissible relative humidity (operation): ⤠95 % (at 25°C, non-condensing) Shock: 18 ms, 30g, in each space direction (according to IEC 60068-2-27) Vibration (operation): 2.3g |
| Standards and regulations | Overvoltage category EN 61010-1: II(â¤4000m) EN61010-2-201: II(â¤4000m) Protective extra-low voltage Standard designation: Protective extra-low voltage Standards/specifications: IEC 61010-1 (SELV) IEC 61010-2-201 (PELV) |
| Approvals | UL approval Identification: UL/C-UL Listed UL61010-1 UL approvalâ Identification: UL/C-UL Listed UL61010-2-201 UL approvalââ Identification: UL/C-UL Listed ANSI/ISA-12.12.01 Class I, Division 2, Groups A, B, C, D T4 (Hazardous Location) CSA Identification: CAN/CSA-C22.2 No.61010-1-12 CSAâ Identification: CAN/CSA-IEC 61010-2-201 CSAââ Identification: CAN/CSA-C22.2 No. 213 Class I, Division 2, Groups A, B, C, D T4 (Hazardous Location) CB scheme Identification: IEC 61010-1 IEC 61010-2-201 DNV Identification: Class Guideline DNVGL-CG-0339 Note: Location classes: TemperatureD (see Application/Limitation), HumidityB, VibrationA/C, EMCB |
| EMC data | Low Voltage Directive: Conformance with Low Voltage Directive 2014/35/EC EMC requirements for noise emission: EN61000-6-3 EN61000-6-4 EMC requirements for noise immunity: EN61000-6-1 EN61000-6-2 Noise immunity: Immunity in accordance with EN61000-6-1 (residential), EN61000-6-2 (industrial), and EN61000-6-5 (power station equipment zone), IEC/EN61850-3 (power supply) Electromagnetic compatibility: Conformance with EMC Directive 2014/30/EU Noise emission: Additional basic standard EN 61000-6-5 (immunity in power station), IEC/EN 61850-3 (energy supply) Electrostatic discharge Standards/regulations: EN61000-4-2 Electrostatic dischargeâ Contact discharge: 8 kV (Test Level 4) Discharge in air: 15 kV (Test Level 4) Comments: Criterion B Electromagnetic HF field Standards/regulations: EN61000-4-3 Electromagnetic HF fieldâ Frequency range: 80 MHz ... 1 GHz 1 GHz ... 6 GHz 1 GHz ... 6 GHz Test field strength: 20 V/m (Test Level 3) 10 V/m (Test Level 3) 10 V/m (Test Level 3) Comments: Criterion A Fast transients (burst) Standards/regulations: EN61000-4-4 Fast transients (burst)â Input: 4 kV (Test Level 4 - asymmetrical) Output: 4 kV (Test Level 4 - asymmetrical) Signal: 4 kV (Test Level 4 - asymmetrical) Comments: Criterion B Surge voltage load (surge) Standards/regulations: EN61000-4-5 Input: 1 kV (Test Level 3 - symmetrical) 2 kV (Test Level 3 - asymmetrical) Output: 1 kV (Test Level 3 - symmetrical) 2 kV (Test Level 3 - asymmetrical) Signal: 1 kV (Test Level 2 - asymmetrical) Comments: Criterion B Conducted interference Standards/regulations: EN61000-4-6 Conducted interferenceâ I/O/S: asymmetrical Frequency range: 0.15 MHz ... 80 MHz Comments: Criterion A Voltage: 10 V (Test Level 3) Power frequency magnetic field Standards/regulations: EN61000-4-8 Frequency: 16.67 Hz 50 Hz 60 Hz 50 Hz 60 Hz 0 Hz Test field strength: 100 A/m 1 kA/m 300 A/m Additional text: 60 s 3 s DC, 60s Comments: Criterion A Frequency range: 50 Hz ... 60 Hz Criteria Criterion A: Normal operating behavior within the specified limits. Criterion B: Temporary impairment to operational behavior that is corrected by the device itself. |
| ECLASS | ECLASS-11.0: 27040705 ECLASS-12.0: 27040705 ECLASS-13.0: 27040705 |
| ETIM | ETIM 9.0: EC000382 |
| UNSPSC | UNSPSC 21.0: 39121000 |
Description other products
