2908399 PHOENIX CONTACT - Technology Bsa

UM-2KS50/32R/SI/J/DO24V/YCS - Active module

32-channel, 24 V DC output relay module with screw connection and redundant, 50-pos. system connection, fuse and jumper in every output circuit, for Yokogawa ADV551 and ADV561

Product Code: 2908399

Partner cod.: 2908399

PHOENIX CONTACT

Product properties	Product type: Interface module Operating mode: 100% operating factor Mechanical service life: 2x 10⁷ cycles Insulation characteristics: Air clearances and creepage distances, input/output Overvoltage category: III Pollution degree: 2 Insulation characteristics: Air and creepage distances, output/output Insulation: Basic insulation Overvoltage category: II Pollution degree: 2
Electrical properties	Air clearances and creepage distances, input/output Rated insulation voltage: 300 V Rated surge voltage: 6 kV (Reinforced insulation) Air and creepage distances, output/output Rated insulation voltage: 300 V Rated surge voltage: 2.5 kV Supported controller YOKOGAWA CENTUM VP Suitable I/O card: ADV551 ADV561 NFDV551 NFDV561
Input data	Nominal input voltage U_N: 24 VDC Input voltage range in reference to U_N: 0.8 ... 1.2 Input voltage range: 19.2 VDC ... 28.8 VDC Typical input current at U_N: 7 mA Typical response time: 5 ms Typical release time: 6 ms Protective circuit: Freewheeling diode; Freewheeling diode Status display/channel: green LED
Output data	Switching Contact switching type: 1 N/O contact Type of switch contact: Single contact Contact material: AgSnO Maximum switching voltage: 24 VDC Minimum switching voltage: 5 V (100 mA) Limiting continuous current: 1.5 A (32°C) 1 A (45°C) 0.5 A (50°C) Max. total current of voltage supply: 10 A (50°C) Min. switching current: 1 mA (24V) Interrupting rating (ohmic load) max.: 48 W (24VDC)
Connection data	Controller level Connection method: Yokogawa KS-compatible Number of connections: 2 Number of positions: 50 Field level Connection method: Screw connection Number of connections: 32 Number of positions: 2 Conductor cross section rigid: 0.2 mm² ... 4 mm² Conductor cross section flexible: 0.2 mm² ... 2.5 mm² Conductor cross section AWG: 24 ... 12 Supply Connection method: Screw connection Number of connections: 4 Number of positions: 2 Conductor cross section rigid: 0.2 mm² ... 4 mm² Conductor cross section flexible: 0.2 mm² ... 2.5 mm² Conductor cross section AWG: 24 ... 12
Signaling	Status display present: Yes
Dimensions	Dimensional drawing: https://dam-mdc.phoenixcontact.com/rendition/156443151564/f22b76dc1246b34282134f0c13ef7bc4/-S204x204-FJPG Width: 217.5 mm Height: 127.5 mm Depth: 60.5 mm
Environmental and real-life conditions	Ambient conditions Degree of protection: IP00 Degree of protection (Installation location): Ã¢¥ IP54 (Installation location) Ambient temperature (operation): -20°C ... 50°C Ambient temperature (storage/transport): -20°C ... 80°C Permissible humidity (operation): 10 % ... 95 % (non-condensing)
Standards and regulations	Air clearances and creepage distances, input/output Standards/regulations: ENIEC 61010-2-201 Air and creepage distances, output/output Standards/regulations: ENIEC 61010-2-201
Mounting	Mounting type: DIN rail mounting Assembly instructions: in rows with zero spacing Mounting position: any
Notes	General: Do not connect adjacent channels to SELV/PELV and FELV. No additional touch protection is required when using a SELV/PELV voltage (Ã¢¤ 25VAC or 60VDC). At least one functional insulation against adjacent modules is complied with (in the support rail direction). If the application has stricter requirements for the insulation (basic insulation or reinforced insulation), they must be realized by applying suitable measures (e.g. partition plates). Do not use for isolation For proper use, the specifications of the installation directive (see Downloads) must be observed. For applications or use with third-party products, the specifications, and the safety and warning instructions of the respective third-party manufacturer must also be met.