Industrial Automation

Mechatronics

Industrial Safety

Panel Components

Sensors and Systems of Vision

Pneumatics

Network Comunications

Automation Cables

Design Software

Access services

Enter your reserved area

Access services

Enter your reserved area

ROCKWELL AUTOMATION 280E-FN-10-R
ROCKWELL AUTOMATION 280E-FN-10-R
ROCKWELL AUTOMATION 280E-FN-10-R
ROCKWELL AUTOMATIONNot available

Starter, Repair Base Mod, EtherNet_IP, Base Module Only, IP67/NEMA 4 Watertight Encl, 10 A Rated Device, Armor Connect Power Media, No Opti on Selection

Base Module for Bulletin 280 Combination Starter, EtherNet/IP, 10 A Rated Device
Product Code: 280E-FN-10-R
Partner cod.: 280E-FN-10-R
ROCKWELL AUTOMATION


Diminuisci la quantità
Aumenta la quantità
Tecnichal data
Tecnichal data
Degree of protection (IP)IP67
Shipping weight, approx10.4 kg
ShockOperational: 15 G
Wire strip lengthPower and ground terminals: 0.35 inch (9 mm)
VibrationOperational, 1 G, 0.15 mm (0.006 inch) displacement
Tightening torquePower and ground terminals: 4.5 lb.inch per UL/NEMA (secondary terminal)
Mechanical life operationsContactor C23 (AC-3): 13000000 operations per IEC
Disconnect lock outRecommend 8 mm (5/16 inch) lock shackle or hasp. The hasp should not exceed 8 mm (5/16 inch) when closed.
Altitude2000 m
Operating temperature-20 °C
Storage and transportation temperature-25 °C
Humidity5...95% (noncondensing)
Protection against shockPower circuit: IP2X per IEC
Surge transient1 kV (12) L-L, 2 kV (2) L-N (earth)
Radiated emissionsClass A, Group 1, equivalent to C2 emissions
Conducted radio frequency emissions10V rms communications cables, 10V rms (PE), 150 kHz...80 MHz
Radio frequency electromagnetic field10V/m, 80 KHz...1 GHz, 3V/m, 1.4 GHz...2 GHz, 1V/m, 2.0 GHz ...2.7 GHz
Degree of protection (NEMA)4
Pollution degree3
Electrostatic discharge4 kV contact and 8 kV Air
Fast transient2 kV (power), 2 kV (PE), 1 kV (communications and control)
Overload current range1.1 A
Base moduleBase module
Short circuit protection10 A rated device
DHCP timeoutEthernet port: 30 s
Web serverEmbedded web server
Overvoltage categoryControl circuit: III per IEC
Rated operational currentPower circuit: 5.5 A maximum
Rated impulse voltagePower circuit: 6 kV
IP addressEthernet port: DHCP enabled by default
PortsEthernet port: embedded switch with 2 ports
Rated input operation voltageSourced from control circuit (A3/A2): 24V DC
Input OFF-state currentSourced from control circuit (A3/A3): <1.5 mA
Module inrush currentEtherNet/IP version: 1.09 A (A1/A2 with HOA)
Module steady currentEtherNet/IP version: 0.3 A (A3/A2 without HOA)
Total control power (running)EtherNet/IP version: 7.2 W (A3/A2 without HOA)
Operating frequencyPower circuit: 50/60 Hz
Input ON-state currentSourced from control circuit (A3/A3): 7.2 mA @ 24V DC
Ethernet receptaclesEthernet port: 2 D-coded, 4-pin female M12 connectors
Number of contactsOutput ratings - sourced from control circuit (A1/A2): 2
Voltage status onlySensor source: 11...26.4V DC from unswitched power (A3-A2)
Trip rating120% of full load current (FLC) setting
Type of currentOutput ratings - sourced from control circuit (A1/A2): 24V DC
Input compatibilitySourced from control circuit (A3/A3): IEC 1133 Type 1+ per IEC
Application in industrial area permitted (SCPD list)Size per NFPA 70 (NEC) or NFPA 79 for group motor applications
ON-state voltage, maxOutput ratings - sourced from control circuit (A1/A2): 1.5V DC
Rated output operation voltageSourced from control circuit (A1/A2): 26.4V DC
Insulation voltagePower circuit: rated 600V
Communication rateEthernet port: 10/100 Mbs with auto negotiate half duplex and full duplex
Dielectric withstandPower circuit: 2500V AC per IEC
Type of contactsOutput ratings - sourced from control circuit (A1/A2): normally open (N.O.)
Current availableSensor source: 50 mA maximum per input, 200 mA for any single point
Type of control circuitOutput ratings - sourced from control circuit (A1/A2): solid state sourcing output
Conventional thermal current (Ith)Output ratings - sourced from control circuit (A1/A2): 0.5 A each, 1 A maximum combined
Circuit breaker operational current rating, max60 A @ 480V (with gland type: CR or DR)
RMS symmetrical amperes65 kA @ 480Y/277V (with gland type: RR)
Rated operation voltagePower circuit: 200...575V
3-phase power/motor cable connection3-phase power media connectivity
Input filter - software selectableSourced from control circuit (A3/A3): settable from 0...64 ms in 1 ms increments (ON to OFF)
Fuse operational current rating, maxTime delay: 20 A @ 480Y/277V (with gland type: RR)
Total control power (pick up)EtherNet/IP version: 7.2 W (A3/A2 without HOA)
Peak output currentOutput ratings - sourced from control circuit (A1/A2): current limited 2-8 amps (5 amps nominal) @ 24V DC
Trip classClass 10, 15, 20
Operational power ratingFull voltage starters âۉ€œ IP67/NEMA Type 4: 3 Hp @ 460V AC, 60 Hz (Current rating 1.1...5.5 A)
DataEthernet port: Transported over both TCP and UDP, Minimum of 500 I/O packets/second (pps), Supports up to 150 concurrent TCP sockets
Input frequency response, maxSourced from control circuit (A3/A3): 200 Hz (DeviceLogix response is greater than 200 Hz. Network response depends on control system network performance.)
Device connectionsTCP port supports 5 concurrent incoming connections
Number of digital inputs4
Number of digital outputs2
Application in industrial area permittedYes
Max. output frequency400 Hz
Supporting protocol for EtherNet/IPYes
Mains frequency50/60 Hz
Short circuit protection device performance (SCPD) typeType 1
Utilization categoryPower circuit: AC-3 per IEC
SecurityWeb server: login and password configurable
Input OFF-state voltage rangeSourced from control circuit (A3/A3): 0...5V DC
Input ON-state voltage rangeSourced from control circuit (A3/A3): 10...26V DC
ConfigurationWeb server: status, diagnostics and configuration tabs
E-mailWeb server: support simple mail transfer protocol (SMTP)
Off-state leakage current, maxOutput ratings - sourced from control circuit (A1/A2): 10 μA
Blocking voltage, maxOutput ratings - sourced from control circuit (A1/A2): 35V DC
Fault recoveryDLR: ring recovery time is less than 3 ms for a 50 node network
DC control voltageEtherNet/IP version: 24V DC (A1/A2, A3/A2, without and without HOA)
Device level ringBeacon-based performance including IEEE 1588 end to end transparent clock
Load typesOutput ratings - sourced from control circuit (A1/A2): resistive or light inductive
Surge suppressionOutput ratings - sourced from control circuit (A1/A2): integrated diode, clamps @ 35V DC
Cycle rate, maxOutput ratings - sourced from control circuit (A1/A2): 30 operations/minute capacitive and inductive loads
Thermo-protectionOutput ratings - sourced from control circuit (A1/A2): integrated short circuit and over current protection
Wire sizePower and ground terminals: #16...#10 AWG per UL/NEMA (primary/secondary terminal)
Number of poles3