1078686 PHOENIX CONTACT - Technology Bsa

RIF-1-RPT-LDP-24DC/1ICT - Relay Module

Preassembled relay module with Push-in connection, consisting of: relay base, power contact relay, plug-in display/interference suppression module, retaining bracket. Contact switching type: 1 N/O contact, max. inrush current up to 800A, 24VDC input voltage

Cod. Articolo: 1078686

Cod. Fornitore: 1078686

PHOENIX CONTACT

Notes	General: FBS 2-6... plug-in bridge for the input side (A2) and FBS-2-8... plug-in bridge for the output side (11/21) At least a basic level of insulation is maintained against adjacent modules in the DIN rail direction. If the application has higher requirements on the insulation (reinforced insulation), then these must be realized through suitable measures (e.g. partition plates). The system installer must ensure the touch protection of the product (at voltages > 25 V AC/60 V DC). The product is a built-in device without protection against direct contact.
Product properties	Product type: Relay Module Product family: RIFLINEcomplete Application: high inrush currents Operating mode: 100% operating factor Mechanical service life: 3x 10⁷ cycles Insulation characteristics Insulation: Safe isolation, reinforced insulation Insulation characteristics: Standards/regulations Insulation: Safe isolation, reinforced insulation Overvoltage category: III Pollution degree: 2
Electrical properties	Maximum power dissipation for nominal condition: 0.43 W Test voltage (Winding/contact): 4 kV AC (50Hz, 1min., winding/contact) Standards/regulations Rated surge voltage: 6 kV
Input data	Coil side Nominal input voltage U_N: 24 VDC Input voltage range: 19.2 VDC ... 33.6 VDC (20°C) Input voltage range in reference to U_N: see diagram Drive and function: monostable Drive (polarity): polarized Typical input current at U_N: 18 mA Typical response time: 8 ms Typical release time: 10 ms Coil voltage: 24 VDC Protective circuit: Reverse polarity protection; Polarity protection diode Surge protection; Freewheeling diode Operating voltage display: Yellow LED
Output data	Switching Contact switching type: 1 N/O contact Type of switch contact: Single contact Note regarding the switch contact: With tungsten leading contact Contact material: AgSnO Maximum switching voltage: 250 V AC/DC Minimum switching voltage: 12 V (100 mA) Limiting continuous current: 6 A 10 A (Value is permissible if connections 11 and 21, as well as connections 14 and 24 are bridged.) Maximum inrush current: 165 A (20ms) 800 A (200 µs) Min. switching current: 100 mA (12VDC) Interrupting rating (ohmic load) max.: 264 W (at 24VDC, observe contact derating) 58 W (at 48 V DC) 48 W (at 60 V DC) 50 W (at 110 V DC) 80 W (at 220 V DC) 2750 VA (at 250VAC, observe contact derating) Switching capacity min.: 1200 mW Utilization category CB Scheme (IEC 60947-5-1): AC15, 6 A/250 V (N/O contact) DC13, 2 A/24 V (N/O contact)
Connection data	Connection method: Push-in connection Stripping length: 8 mm Conductor cross section rigid: 0.14 mm² ... 1.5 mm² Conductor cross section flexible: 0.14 mm² ... 1.5 mm² 0.14 mm² ... 1.5 mm² (Ferrule with plastic sleeve) 0.14 mm² ... 1 mm² (Ferrule with plastic sleeve, two conductors on double terminal block) Conductor cross section AWG: 26 ... 16 (solid) 26 ... 16 (flexible)
Dimensions	Drill hole Diameter: 3.2 mm Width: 16 mm Height: 96 mm Depth: 75 mm
Environmental and real-life conditions	Ambient conditions Degree of protection (Relay): RT II (Relay) Degree of protection (Relay base): IP20 (Relay base) Degree of protection (Installation location): Ã¢¥ IP54 (Installation location) Ambient temperature (operation): -40°C ... 70°C Ambient temperature (storage/transport): -40°C ... 85°C Altitude: Ã¢¤ 2000 m
Approvals	Corrosive gas test Identification: ISA-S71.04. G3 Harsh Group EN60068-2-60
Standards and regulations	Standards/regulations Standards/regulations: IEC 60947-5-1
Mounting	Mounting type: DIN rail mounting Assembly instructions: in rows with zero spacing Mounting position: any