1095772 PHOENIX CONTACT - Technology Bsa

SACC-FS-4PL SCO - Connector

Connector, 4-position, Socket straight M12, coding: A, Push-in connection, knurl material: Zinc die-cast, nickel-plated, external cable diameter 4 mm ... 8 mm

Cod. Articolo: 1095772

Cod. Fornitore: 1095772

PHOENIX CONTACT

Notes	General: NOTE: Observe the permissible bending radii when laying conductors, since the degree of protection may be put in jeopardy if the bending forces are too high. Alleviate mechanical loads upstream of the connector, e.g.by using cable ties.
Mounting	Assembly instructions: The wires can be connected both with ferrules and without ferrules Connection method: Push-in connection
Product properties	Product type: Circular connector (cable-side) Number of positions: 4 No. of cable outlets: 1 Shielded: no Coding: A Cable outlet: straight Insulation characteristics Overvoltage category: II Degree of pollution: 3
Dimensions	Dimensional drawing: https://dam-mdc.phoenixcontact.com/rendition/156443151564/813e7dabee251143bfbe11407e435636/-S204x204-FJPG Length: 58 mm External dimensions Outside diameter: 4 mm ... 8 mm Housing Diameter housing: 19 mm
Material specifications	Material: PBT PA 6 Flammability rating according to UL 94: V0 Seal material: NBR Material of grip body: PA 6.6 Contact material: CuSn Contact surface material: Ni/Au Contact carrier material: PA 6.6 Material for screw connection: Zinc die-cast, nickel-plated Standards/regulations: PA 6.6: Fire protection in rail vehicles - requirement sets R22, R23, R24, and R26 acc. to DINEN45545-2 (Risk level HL1 - HL3) PA 6: Fire protection in rail vehicles - requirement sets R22, R23, and R24 acc. to DINEN45545-2 (Risk level HL1 - HL3) PBT: Fire protection in rail vehicles - requirement sets R22, R23, R24, and R26 acc. to DINEN45545-2 (Risk level HL1 - HL2, R26: HL3)
Connection data	Conductor connection Connection method: Push-in connection Connection cross section: 0.14 mm² ... 0.75 mm² (without ferrule) 0.08 mm² ... 0.5 mm² (with ferrule) 0.14 mm² ... 0.75 mm² (solid) Connection cross section AWG: 26 ... 18 (without ferrule) 28 ... 20 (with ferrule) Stripping length of the individual wire: 8 mm Tightening torque: 0.4 Nm (M12 knurl) 0.4 Nm (Connector with coupling sleeve) 1.5 Nm (Pressure nut with coupling sleeve)
Electrical properties	Rated surge voltage: 2.5 kV Contact resistance: Ã¢¤ 5 mÃ© Insulation resistance: Ã¢¥ 100 MÃ© Nominal voltage U_N: 250 VAC 250 VDC Nominal current I_N: 4 A
Mechanical properties	Mechanical data Insertion/withdrawal cycles: Ã¢¥ 100 (Quantity: 500 with Phoenix Contact mating connector)
Connector	Connection 1 Head design: Socket Head cable outlet: straight Head thread type: M12 Coding: A
Cable/line	Stripping length of the individual wire: 8 mm
Environmental and real-life conditions	Ambient conditions Degree of protection: IP65 IP67 Ambient temperature (operation): -40°C ... 85°C (Plug / socket)
Standards and regulations	Testing Standards/regulations: PA 6.6: Fire protection in rail vehicles - requirement sets R22, R23, R24, and R26 acc. to DINEN45545-2 (Risk level HL1 - HL3) PA 6: Fire protection in rail vehicles - requirement sets R22, R23, and R24 acc. to DINEN45545-2 (Risk level HL1 - HL3) PBT: Fire protection in rail vehicles - requirement sets R22, R23, R24, and R26 acc. to DINEN45545-2 (Risk level HL1 - HL2, R26: HL3) M12 Standard designation: M12 connector Shock, vibration Standards/specifications: IEC 61076-2-101 EN50155:2001