1362791 PHOENIX CONTACT - Technology Bsa

Input data	AC operation Supply system configuration: Star network (TN, TT, IT (PE)) Nominal input voltage range: 3x 400 V AC ... 500 V AC Input voltage range: 3x 400 V AC ... 500 V AC -20 % ... +10 % 2x 400 V AC ... 500 V AC Ã±10 % Typical national grid voltage: 3x 400 V AC 3x 480 V AC Voltage type of supply voltage: AC Inrush current: < 13 A (25 °C) Inrush current integral (I²t): < 0.33 A²s Frequency range (f_N): 50 Hz ... 60 Hz Ã±10 % Mains buffering time: typ. 28 ms (3x 400 V AC) typ. 28 ms (3x 480 V AC) Current consumption: 3x 0.77 A (3x 400 V AC) 3x 0.63 A (3x 500 V AC) 2x 1.37 A (2x 400 V AC) 2x 1.13 A (2x 500 V AC) Protective circuit: Transient protection; Varistor Power factor (cos phi): 0.93 (3x 480 V AC) Device mains fuse: 3.15 A internal (device protection) Recommended breaker for input protection: 3x 6 A ... 16 A (Characteristic B, C, D, K or comparable) Discharge current to PE: < 3.5 mA
Output data	Efficiency: typ. 94.4 % (3x 400 V AC) typ. 94.5 % (3x 480 V AC) Nominal output voltage: 24 V DC Setting range of the output voltage (U_Set): 24 V DC ... 28 V DC (> 24 V DC, constant capacity restricted) Nominal output current (I_N): 20 A Dynamic Boost (I_Dyn.Boost): max. 30 A (5 s) No. of channels: 8 Nominal current per channel: 1 A 2 A 3.8 A 4 A 6 A 8 A 10 A Waiting time after switch off of a channel: 5 s Switch-on delay of the channels: 100 ms Short-circuit-proof: yes No-load proof: yes Derating: 60 °C ... 70 °C Crest factor: typ. 1.51 (3x 400 V AC) typ. 1.69 (3x 480 V AC) Output power (P_N): 480 W Output power (P_{Dyn. Boost}): max. 720 W (5 s) Connection in parallel: no Connection in series: no Max. capacitive load: 30 mF Feedback voltage resistance: Ã¢Ã¢°¤ 35 V DC Protection against overvoltage at the output (OVP): Ã¢Ã¢°¤ 35 V DC Residual ripple: typ. 15 mV_PP (with nominal values) Control deviation: < 1 % (change in load, static 10 % ... 90 %) < 3 % (change in load, dynamic 10 % ... 90 %) < 0.1 % (change in input voltage Ã±10 %) Rise time: Ã¢Ã¢°¤ 1 s (U_Out = 10 % ... 90 %) Minimum no-load power dissipation: < 3 W (3x 400 V AC) Maximum no-load power dissipation: < 3.1 W (3x 480 V AC) Minimum nominal load power dissipation: < 26.08 W (3x 400 V AC) Power loss nominal load max.: < 27.35 W (3x 480 V AC) Integrated fuse protection: yes Signal relay 13/14 Position: 3.x Position marking: 3.1 (13), 3.2 (14) Switch contact (floating): OptoMOS Switching voltage: max. 30 V DC (SELV) Current carrying capacity: max. 100 mA State condition: U_Out > 21 V DC and I_Out < 0.9 x I_N (Contact closed) U_Out < 21 V DC or I_Out > 0.9 x I_N (averaging over 60 s) (Contact open) Channel triggered or defective or OVP active
Connection data	Input Position: 1.x Connection technology Position marking: 1.1 (L1), 1.2 (L2), 1.3 (L3), 1.4 (Ã¯Ã¢¬µ) Conductor connection Connection method: Push-in connection rigid: 0.2 mm² ... 4 mm² 1.5 mm² (recommended) flexible: 0.2 mm² ... 2.5 mm² 1.5 mm² (recommended) flexible with ferrule without plastic sleeve: 0.25 mm² ... 2.5 mm² 1.5 mm² (recommended) flexible with ferrule with plastic sleeve: 0.25 mm² ... 2.5 mm² 1.5 mm² (recommended) rigid (AWG): 24 ... 12 (Cu) 16 (recommended) Stripping length: 10 mm (Rigid/flexible/ferrule) Output Position: 2.x Connection technologyÃ¢Ã¢¬Ã¢¹ Position marking: 2.1, 2.2, 2.3, 2.4, 2.5, 2.6, 2.7, 2.8 (+) Conductor connectionÃ¢Ã¢¬Ã¢¹ Connection method: Push-in connection rigid: 0.2 mm² ... 4 mm² 1.5 mm² (recommended) flexible: 0.2 mm² ... 2.5 mm² 1.5 mm² (recommended) flexible with ferrule without plastic sleeve: 0.25 mm² ... 2.5 mm² (Cu) 1.5 mm² (recommended) flexible with ferrule with plastic sleeve: 0.25 mm² ... 2.5 mm² 1.5 mm² (recommended) rigid (AWG): 24 ... 12 (Cu) 16 (recommended) Stripping length: 10 mm (Rigid/flexible/ferrule) OutputÃ¢Ã¢¬Ã¢¹ Position: 2.x Connection technologyÃ¢Ã¢¬Ã¢¹Ã¢Ã¢¬Ã¢¹ Position marking: 2.9, 2.10 (-) Conductor connectionÃ¢Ã¢¬Ã¢¹Ã¢Ã¢¬Ã¢¹ Connection method: Push-in connection rigid: 0.2 mm² ... 10 mm² 4 mm² (recommended) flexible: 0.2 mm² ... 6 mm² 4 mm² (recommended) flexible with ferrule without plastic sleeve: 0.25 mm² ... 6 mm² 4 mm² (recommended) flexible with ferrule with plastic sleeve: 0.25 mm² ... 6 mm² 4 mm² (recommended) rigid (AWG): 24 ... 8 (Cu) 12 (recommended) Stripping length: 12 mm (Rigid/flexible/ferrule) Signal Position: 3.x Connection technologyÃ¢Ã¢¬Ã¢¹Ã¢Ã¢¬Ã¢¹Ã¢Ã¢¬Ã¢¹ Position marking: 3.1 (13), 3.2 (14) Conductor connectionÃ¢Ã¢¬Ã¢¹Ã¢Ã¢¬Ã¢¹Ã¢Ã¢¬Ã¢¹ Connection method: Push-in connection rigid: 0.2 mm² ... 1.5 mm² 0.5 mm² (recommended) flexible: 0.2 mm² ... 1.5 mm² 0.5 mm² (recommended) flexible with ferrule without plastic sleeve: 0.25 mm² ... 1.5 mm² (Cu) 0.5 mm² (recommended) flexible with ferrule with plastic sleeve: 0.25 mm² ... 0.75 mm² 0.5 mm² (recommended) rigid (AWG): 24 ... 16 (Cu) 20 (recommended) Stripping length: 10 mm (Rigid/flexible/ferrule) Communication Position: 5.x Connection technologyÃ¢Ã¢¬Ã¢¹Ã¢Ã¢¬Ã¢¹Ã¢Ã¢¬Ã¢¹Ã¢Ã¢¬Ã¢¹ Position marking: 5.1 (L+), 5.2 (C/Q), 5.3 (L-) Conductor connectionÃ¢Ã¢¬Ã¢¹Ã¢Ã¢¬Ã¢¹Ã¢Ã¢¬Ã¢¹Ã¢Ã¢¬Ã¢¹ Connection method: Push-in connection rigid: 0.2 mm² ... 1.5 mm² 0.5 mm² (recommended) flexible: 0.2 mm² ... 1.5 mm² 0.5 mm² (recommended) flexible with ferrule without plastic sleeve: 0.25 mm² ... 1.5 mm² (Cu) 0.5 mm² (recommended) flexible with ferrule with plastic sleeve: 0.25 mm² ... 0.75 mm² 0.5 mm² (recommended) rigid (AWG): 24 ... 16 (Cu) 20 (recommended) Stripping length: 10 mm (Rigid/flexible/ferrule)
Interfaces	IO-Link Specification: V1.1 Interface: IO-Link Number of interfaces: 1 Connection method: Push-in connection Position: 5.x Position marking: 5.1 (L+), 5.2 (C/Q), 5.3 (L-) Transmission physics: 3-wire, standard industrial cable Reverse polarity protection: yes Transmission speed: 38.4 kbps (COM2) Cycle time: 40 ms Amount of process data: 6 Byte (Input data) Device ID: 040116_hex/262422_dez Vendor ID: 00B0_hex / 176_dez
Signaling	LED signaling Types of signaling: LED DC OK Ã¢Ã¢¬Ã¢ signal state operation (U_N = 24 V DC, I_Out = I_N) Function: Visual operating state display Color: red, yellow, green (multicolor LED) LED off: Supply voltage input AC not present (Off) LED on (green), DC OK: U_Out > 21 V DC and I_Out < 0.9 x I_N (On (green), DC OK) LED on (yellow), IOut > 90%: U_Out > 21 V DC and I_Out > 0.9 x I_N (On (yellow), I_Out > 90% ) LED on (flashing red) OVP: U_OUT > OVP (Over voltage protection) (On (flashing red))
Electrical properties	Number of phases: 3.00 Insulation voltage input/output: 6 kV DC (type test) 3.1 kV DC (routine test)
Product properties	Product type: Power supply Product family: TRIO POWER MTBF (IEC 61709, SN 29500): > 1100000 h (25 °C) > 600000 h (40 °C) > 230000 h (60 °C) Environmental protection directive: RoHS Directive 2011/65/EU WEEE Reach Data management status Article revision: 00 Insulation characteristics Protection class: I Degree of pollution: 2
Dimensions	Item dimensions Width: 88 mm Height: 135 mm Depth: 132 mm 125 mm (Device depth (DIN rail mounting)) Installation dimensions Installation distance right/left (active): 15 mm / 15 mm Installation distance right/left (passive): 0 mm / 0 mm (Ã¢Ã¢°¤ 40 °C)
Mounting	Mounting type: DIN rail mounting Assembly note: alignable: 0 mm horizontally, 30 mm vertically Mounting position: horizontal DIN rail NS 35, EN 60715 With protective coating: no
Material specifications	Flammability rating according to UL 94: V0 (Housing, terminal blocks) Hood version: Polycarbonate Side element version: Aluminum
Environmental and real-life conditions	Ambient conditions Degree of protection: IP20 Ambient temperature (operation): -25 °C ... 70 °C (> 60 °C Derating: 2,5 %/K) Ambient temperature (storage/transport): -40 °C ... 85 °C Ambient temperature (start-up type tested): -40 °C Maximum altitude: Ã¢Ã¢°¤ 5000 m (> 2000 m, Derating: 10 %/1000 m) Max. permissible relative humidity (operation): Ã¢Ã¢°¤ 95 % (at 25 °C, non-condensing) Shock (operation): 18 ms, 30g, per spatial direction (IEC 60068-2-27) Vibration (operation): 10 Hz ... 50 Hz, amplitude Ã±0.2 mm (IEC 60068-2-6) 50 Hz ... 150 Hz, 2.3g, 90 min.
Standards and regulations	Overvoltage category EN 61010-1: III (Ã¢Ã¢°¤ 2000 m) II (Ã¢Ã¢°¤ 5000 m) Overvoltage categoryÃ¢Ã¢¬Ã¢¹ EN 61010-2-201: III (Ã¢Ã¢°¤ 2000 m) II (Ã¢Ã¢°¤ 5000 m) Safety of power supply units up to 1100 V (insulation distances) Standard designation: Safety of power supply units up to 1100 V (insulation distances) Standards/specifications: DIN EN 61558-2-16 Electrical safety Standard designation: Electrical safety Standards/specifications: IEC 61010-2-201 (SELV) Electronic equipment for use in power installations Standard designation: Equipping high voltage installations with electronic equipment Standards/specifications: EN 50178/VDE 0160 (PELV) Safety for measurement, control, and laboratory equipment Standard designation: Safety for equipment for measurement, control, and laboratory use Standards/specifications: IEC 61010-1 Protective extra-low voltage Standard designation: Protective extra-low voltage Standards/specifications: IEC 61010-1 (SELV) IEC 61010-2-201 (PELV) Safe isolation Standard designation: Safe isolation Standards/specifications: IEC 61558-2-16 IEC 61010-2-201 Limitation of harmonic line currents Standard designation: Limitation of harmonic line currents Standards/specifications: EN 61000-3-2 Mains variation/undervoltage Standard designation: Mains variation/undervoltage Standards/specifications: SEMI F47 EN 61000-4-11
Approvals	UL Identification: UL/C-UL Listed UL 61010-1 ULÃ¢Ã¢¬Ã¢¹ Identification: UL/C-UL Listed UL 61010-2-201 UL/CSA Identification: UL 1310 / CSA C22.2 No. 223 (NEC Class 2) ULÃ¢Ã¢¬Ã¢¹Ã¢Ã¢¬Ã¢¹ Identification: UL 2367 (Standard for Safety for Solid State Overcurrent Protectors) ANSI/UL Identification: PROCESS CONTROL EQUIPEMENT FOR HAZARDOUS LOCATIONS (EN) Ã¯Ã¢· This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D, Hazardous Locations, or non-hazardous locations only. (FR) Ã¯Ã¢· Cet appareil convient uniquement pour une utilisation en atmosphÃ¨res explosibles de classe I, division 2, groupes A, B, C et D ou en atmosphÃ¨res non explosibles. (EN) Ã¯Ã¢· WARNING: Explosion Hazard - Do not connect or disconnect equipment unless power has been switched off or the area is known to be non-hazardous. (FR) Ã¯Ã¢· AVERTISSEMENT : risque d'explosion - ne pas connecter ou dÃ©connecter les Ã©quipements sauf si l'alimentation a Ã©tÃ© coupÃ©e ou si la zone est rÃ©putÃ©e non dangereuse. (EN) Ã¯Ã¢· If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired. (FR) Ã¯Ã¢· Si l'Ã©quipement est utilisÃ© d'une maniÃ¨re non spÃ©cifiÃ©e par le fabricant, la protection fournie par cet Ã©quipement peut Ãªtre altÃ©rÃ©e. (EN) Ã¯Ã¢· This equipement must be installed in a suitable, tool secured/key locked enclosure. (FR) Ã¯Ã¢· Cet Ã©quipement doit Ãªtre installÃ© dans un boÃ®tier appropriÃ©, verrouillÃ© par une clÃ© ou dont l'ouverture nÃ©cessite l'utilisation d'un outil.
EMC data	Electromagnetic compatibility: Conformance with EMC Directive 2014/30/EU Low Voltage Directive: Conformance with Low Voltage Directive 2014/35/EC Interference emission: Interference emission in accordance with EN 61000-6-3 (residential and commercial) and EN 61000-6-4 (industrial) Noise immunity: Immunity in accordance with EN 61000-6-1 (residential), EN 61000-6-2 (industrial) Conducted noise emission: EN 55016 EN 61000-6-3 (Class B) Noise emission: EN 55016 EN 61000-6-3 (Class B) Harmonic currents Standards/regulations: EN 61000-3-2 EN 61000-3-2 (Class A) Frequency range: 0 kHz ... 2 kHz Flicker Standards/regulations: EN 61000-3-3 Frequency range: 0 kHz ... 2 kHz Electrostatic discharge Standards/regulations: EN 61000-4-2 Electrostatic dischargeÃ¢Ã¢¬Ã¢¹ Contact discharge: 6 kV (Test Level 3) Discharge in air: 8 kV (Test Level 3) Comments: Criterion B Electromagnetic HF field Standards/regulations: EN 61000-4-3 Electromagnetic HF fieldÃ¢Ã¢¬Ã¢¹ Frequency range: 80 MHz ... 1 GHz 1 GHz ... 6 GHz Test field strength: 10 V/m (Test Level 3) Comments: Criterion A Fast transients (burst) Standards/regulations: EN 61000-4-4 Fast transients (burst)Ã¢Ã¢¬Ã¢¹ Input: asymmetrical 2 kV (Test Level 3) Output: asymmetrical 2 kV (Test Level 3) Signal: asymmetrical 1 kV (Test Level 3) Comments: Criterion A Surge voltage load (surge) Standards/regulations: EN 61000-4-5 Surge voltage load (surge)Ã¢Ã¢¬Ã¢¹ Input: symmetrical 1 kV (Test Level 3) asymmetrical 2 kV (Test Level 3) Output: symmetrical 0.5 kV (Test Level 2) asymmetrical 1 kV (Test Level 2) Signal: asymmetrical 1 kV (Test Level 2) Comments: Criterion B Conducted interference Standards/regulations: EN 61000-4-6 Conducted interferenceÃ¢Ã¢¬Ã¢¹ I/O/S: asymmetrical Frequency range: 0.15 MHz ... 80 MHz Comments: Criterion A Voltage: 10 V (Test Level 3) Voltage dips Standards/regulations: EN 61000-4-11 Voltage: 480 V AC Frequency: 50 Hz Voltage dip: 70 % 40 % 0 % Number of periods: 25 periods 10 periods 1 period Additional text: Class 3 Comments: Criterion A Criterion B Criterion A Criteria Criterion A: Normal operating behavior within the specified limits. Criterion B: Temporary impairment to operational behavior that is corrected by the device itself. Criterion C: Temporary adverse effects on the operating behavior, which the device corrects automatically or which can be restored by actuating the operating elements.