Automazione Industriale

Meccatronica

Sicurezza Industriale

Componenti Quadri

Sensori e Sistemi di Visione

Pneumatica

Network e Comunicazione

Cavi Speciali

Software di progettazione

Accedi ai servizi

Entra nella tua area riservata

Accedi al B2B
Accedi al tuo account

Accedi ai servizi

Entra nella tua area riservata

Accedi al B2B
Accedi al tuo account
Paese|
||
PHOENIX CONTACT 1405866
PHOENIX CONTACTNon disponibile

VS-M12FSBP-OE-93E-LI/2,0 - Device connector, rear mounting

Device connector, rear mounting, Ethernet CAT5 (100 Mbps), Ethernet CAT5 (100 Mbps), 4-position, PUR, water blue RAL5021, shielded, Socket, straight, M12-SPEEDCON, coding: D, on free cable end, Rear mounting, M16 x 1.5, Bus line, cable length: 2 m, 0.14 mm2, Ethernet flexible CAT5, 2-pair, Alternative product in accordance with RoHS II without Exemption6c (Pb<0.1%) item no.: 1238737
Cod. Articolo: 1405866
Cod. Fornitore: 1405866
PHOENIX CONTACT


Diminuisci la quantità
Aumenta la quantità
Caratteristiche Tecniche
Specifiche
Descrizione
Download
Caratteristiche Tecniche
NotesGeneral: The electrical and mechanical data specified assume that the connector pair is correctly locked and mounted. If the connector is unlocked and if there is a danger of contamination, the connector must be sealed using a protective cap > IP54. Influences arising from litz wires, cables or PCB assembly must also be taken into consideration.
Safety note
Safety note: WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
• The products are suitable for applications in plant, controller, and electrical device engineering.
• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50V AC, conductive connector housings must be grounded
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the corresponding technical data. You will find information:
o On the product
o On the packing label
o In the supplied documentation
o Online at phoenixcontact.com/products under the product
• Only use tools recommended by PhoenixContact
• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
• Ensure that the protective or functional ground has been properly connected.
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).
Product propertiesProduct type: Data cable preassembled
Sensor type: Ethernet
Number of positions: 4
No. of cable outlets: 1
Shielded: yes
Coding: D
Thread type: M12
Insulation characteristics
Overvoltage category: II
Degree of pollution: 3
InterfacesBus system: Ethernet
Signal type/category: Ethernet CAT5 (IEC 11801:2002), 100 Mbps
Ethernet CAT5 (IEC 11801), 100 Mbps
Electrical propertiesRated surge voltage: 2.5 kV
Contact resistance: ≤ 3 mΩ
Insulation resistance: ≥ 100 MΩ
Nominal voltage UN: 48 VAC
60 VDC
Nominal current IN: 4 A (Plug/socket in accordance with IEC 61076-2-101, cable technical data is to be observed)
Transmission medium: Copper
Transmission characteristics (category): CAT5 (IEC 11801:2002)
Mechanical propertiesMechanical data
Insertion/withdrawal cycles: ≥ 100
Material specificationsFlammability rating according to UL 94: V0
Seal material: FKM
Contact material: CuZn
Contact surface material: Ni/Au
Contact carrier material: PA 6.6
Material for screw connection: Zinc die-cast, nickel-plated
Outer sheath, material: PUR
Connection dataConnection technology
Connection method: Bus line
Conductor connection
Contact connection type: Crimp contacts
Connection method: Bus line
Tightening torque: 2 Nm ... 3 Nm (Installation-side)
ConnectorConnection 1
Head design: Socket
Head cable outlet: straight
Head thread type: M12
Head locking type: SPEEDCON
Coding: D
Connection 2
Head design: free cable end
Cable/lineCable length: 2 m
Ethernet flexible CAT5, 2-pair[93E]
Dimensional drawing: https://dam-mdc.phoenixcontact.com/rendition/156443151564/7fe2dbaea8a70742b151e6eb6516da5e/-S204x204-FJPG
Cable weight: 42 kg/km
UL AWM Style: 20963 (80°C/30 V)
Wiring standards/regulations: Electrical requirements EN50288-2-2
Number of positions: 4
Shielded: yes
Cable type: Ethernet flexible CAT5, 2-pair[93E]
Conductor structure: 2x2xAWG26/7, SF/UTP
Signal runtime: 5.3 ns/m
Conductor structure signal line: 7x 0.16 mm
AWG signal line: 26
Conductor cross section: 2x 2x 0.14 mm²
Wire diameter incl. insulation: 0.98 mm
External cable diameter: 6.4 mm ±0.2mm
Outer sheath, material: PUR
External sheath, color: water blue RAL5021
Conductor material: Bare Cu litz wires
Material wire insulation: Foamed PE
Single wire, color: white/orange-orange, white/green-green
Thickness, outer sheath: 1.2 mm
Twisted pairs: 2 cores to the pair
Overall twist: Two pairs with two fillers to the core
Optical shield covering: 70 %
Insulation resistance: ≥ 500 MΩ*km
Coupling resistance: ≤ 100.00 mΩ/m (at 10 MHz)
Loop resistance: ≤ 290.00 Ω/km
Wave impedance: 100 Ω ±5Ω (at 100 MHz)
Cable capacity: approx. 45 nF/km (at 1 kHz)
Nominal voltage, cable: ≤ 100 V (Peak value, not for high-power applications)
Test voltage Core/Core: 700 V (50Hz, 1min.)
Test voltage Core/Shield: 700 V (50Hz, 1min.)
Current carrying capacity of cable: 2 A (according to DINVDE0891-1)
Minimum bending radius, fixed installation: 4 x D
Minimum bending radius, flexible installation: 8 x D
Smallest bending radius, fixed installation: 26 mm
Smallest bending radius, movable installation: 52 mm
Tensile strength: ≤ 80 N
Near end crosstalk attenuation (NEXT): 65.3 dB (with 1 MHz)
56.3 dB (at 4 МHz)
50.3 dB (at 10 MHz)
47.2 dB (at 16 MHz)
45.8 dB (at 20МHz)
42.9 dB (at 31.25МHz)
38.4 dB (at 62.5МHz)
35.3 dB (at 100 MHz)
Power-summated near end crosstalk attenuation (PSNEXT): 62.3 dB (with 1 MHz)
53.3 dB (at 4 МHz)
47.3 dB (at 10 MHz)
44.2 dB (at 16 MHz)
42.8 dB (at 20МHz)
39.9 dB (at 31.25МHz)
35.4 dB (at 62.5МHz)
32.3 dB (at 100 MHz)
Return attenuation (RL): 23 dB (at 4 МHz)
24.1 dB (at 8МHz)
25 dB (at 10 MHz)
25 dB (at 16 MHz)
25 dB (at 20МHz)
23.6 dB (at 31.25МHz)
21.5 dB (at 62.5МHz)
20.1 dB (at 100 MHz)
Shield attenuation: 3.2 dB (with 1 MHz)
6 dB (at 4 МHz)
9.5 dB (at 10 MHz)
12.1 dB (at 16 MHz)
13.6 dB (at 20МHz)
17.1 dB (at 31.25МHz)
24.8 dB (at 62.5МHz)
32 dB (at 100 MHz)
Halogen-free: according to IEC 60754-1
Flame resistance: according to IEC 60332-1-2
in acc. to UL VW1
in accordance with UNECE-R118.03
Resistance to oil: in accordance with EN 60811-2-1
Ambient temperature (operation): -40°C ... 80°C (cable, fixed installation)
-20°C ... 80°C (Cable, flexible installation)
Ambient temperature (installation): -20°C ... 80°C
Environmental and real-life conditionsAmbient conditions
Degree of protection: IP67 (When plugged in)
IP65 (When plugged in)
IP65/IP67
Ambient temperature (operation): -25°C ... 85°C (Plug / socket)
-40°C ... 85°C (without mechanical actuation)
Standards and regulationsM12
Standard designation: M12 connector
Standards/specifications: IEC 61076-2-101
Specifiche
ECLASSECLASS-11.0: 27060308
ECLASS-12.0: 27060308
ECLASS-13.0: 27060308
ETIMETIM 9.0: EC002599
UNSPSCUNSPSC 21.0: 26121600
Descrizione
Assembled Ethernet cable, CAT5e, shielded, 2-pair, AWG 26 stranded (7-wire), RAL 5021 (water blue), M12 flush-type socket, rear/screw mounting with M16 thread on free conductor end, line, length 2 m
Download
PER SCARICARE I DOCUMENTI E' NECESSARIO EFFETTUARE L'ACCESSO AL SITO

Design-In_00002.pdf

Manufacturer_declaration_07193.pdf

Technical_drawing_05883.pdf