Non disponibile 
| Dimensions | Dimensional drawing: https://dam-mdc.phoenixcontact.com/rendition/156443151564/20a984302842e949b5ce7beb58df3766/-S204x204-FJPG Width: 48.8 mm Height: 136 mm Depth: 71.5 mm |
| Interfaces | Inline local bus Connection method: Inline data jumper Transmission speed: 500 kbps Transmission physics: Copper Serial Designation: V.24 (RS-485) serial interface Addressing: Address 1 = Measured gross/net value Address 2 = Measured tare value Termination resistor: 120Ãé Transmission protocol: STX/ETX |
| System properties | Module ID code (dec.): 223 ID code (hex): DF Length code (hex): 03 Length code (dec): 03 Process data channel: 48 bit Input address area: 6 Byte Output address area: 6 Byte Register length: 64 bit Required parameter data: 23 Byte Required configuration data: 5 Byte |
| Input data | Analog Description of the input: Input channels for strain gauge Number of inputs: 2 Connection technology: 6 or 4-wire, twisted pair shielded cable Bridge difference Ud: Measuring range specified by selecting the characteristic Bridge voltage U0: 5 V Measured value representation: 16Ãbit, 20Ãbit, ASCII data record Characteristics: ñ1ÃmV/V, ñ2ÃmV/V, ñ3ÃmV/V, ñ3.33ÃmV/V, ñ4ÃmV/V, ñ5ÃmV/V, ñ6ÃmV/V, manual characteristic value specification Contacts Description: Floating N/O contact Quantity: 2 (Ka1-Kb1, Ka2-Kb2) Contact resistance: < 1 é (typical) 3 é (maximum) Typical response time: typ. 0.2 ms (opening) typ. 2 ms (close) |
| Output data | Analog Output description: Jumper supply Number of outputs: 2 Impedance: > 43 é (per channel) Output voltage: typ. 5 V Output current: max. 115 mA (per channel) |
| Product properties | Type: modular Product type: I/O component Product family: Inline Operating mode: Process data operation with 3 words, PCP with 1 word Diagnostics messages: Failure of the power supply at UANA Error message in the process data Failure of or insufficient communications power UL I/O error message sent to the bus coupler I/O error Error message in the process data |
| Electrical properties | Potentials Power consumption: typ. 1.4 W (Device in nominal operation) max. 3.5 W (Device with maximum load) Potentials: Communications power (U Supply voltage: 7.5 VÃDC (via voltage jumper) Current draw: max. 95 mA typ. 80 mA Potentials: Supply of analog modules (U Supply voltage: 24 VÃDC (via voltage jumper) Supply voltage range: 19.2 VÃDC ... 30 VÃDC (including all tolerances, including ripple) Current draw: typ. 32 mA (in case of typical load of 350 Ohm per channel) 115 mA (with maximum load of 43Ãé and display) 14 mA (for no-load operation without strain gauge or display) Electrical isolation/isolation of the voltage ranges Test voltage: Logic: 500 VÃAC, 50 Hz, 1 min. Test voltage: Analog I/O: 500 VÃAC, 50 Hz, 1 min. Test voltage: RS-485: 500 VÃAC, 50 Hz, 1 min. Test voltage: N/O contact Ka1 - Kb1: 500 VÃAC, 50 Hz, 1 min. Test voltage: N/O contact Ka2 - Kb2: 500 VÃAC, 50 Hz, 1 min. Test voltage: Functional ground: 500 VÃAC, 50 Hz, 1 min. |
| Connection data | Connection technology Connection name: Inline connector Conductor connection Connection method: Spring-cage connection Conductor cross section rigid: 0.08 mm² ... 1.5 mm² Conductor cross section flexible: 0.08 mm² ... 1.5 mm² Conductor cross section AWG: 28 ... 16 Stripping length: 8 mm Inline connector Connection method: Spring-cage connection Conductor cross section, rigid: 0.08 mm² ... 1.5 mm² Conductor cross section, flexible: 0.08 mm² ... 1.5 mm² Conductor cross section AWG: 28 ... 16 Stripping length: 8 mm |
| Environmental and real-life conditions | Ambient conditions Ambient temperature (operation): -25°C ... 55°C Degree of protection: IP20 Air pressure (operation): 70 kPa ... 106 kPa (up to 3000Ãm above sea level) Air pressure (storage/transport): 70 kPa ... 106 kPa (up to 3000Ãm above sea level) Ambient temperature (storage/transport): -25°C ... 85°C Permissible humidity (operation): 10 % ... 95 % (non-condensing) Permissible humidity (storage/transport): 10 % ... 95 % (non-condensing) |
| Standards and regulations | Protection class: III (IEC 61140, ENÃ61140, VDEÃ0140-1) |
| Mounting | Mounting type: DIN rail mounting |
Di seguito alcuni articoli correlati a quello che stai vedendo
