2900326 PHOENIX CONTACT - Technology Bsa

PLC-RPT-110UC/21HC/RW - Relay Module

PLC-INTERFACE for railway applications and high continuous currents, consisting of basic terminal block with Push-in connection and plug-in miniature relay, range: 0.7 x U_N to 1.25 x U_N, temperature class TX: -40°C to +70°C, 1 changeover contact, input voltage 110 V DC

Cod. Articolo: 2900326

Cod. Fornitore: 2900326

PHOENIX CONTACT

Product properties	Product type: Relay Module Product family: PLC-INTERFACE Installation location: Attached to the vehicle body Application: Railway applications Operating mode: 100% operating factor Mechanical service life: approx. 3x 10⁷ cycles Insulation characteristics Insulation: Basic insulation Insulation characteristicsÃ¢ Insulation: Basic insulation Overvoltage category: III Pollution degree: 2
Electrical properties	Maximum power dissipation for nominal condition: 0.5 W Test voltage (Winding/contact): 5 kV_rms (50Hz, 1min., winding/contact) Rated insulation voltage: 250 VAC Rated surge voltage: 6 kV
Input data	Coil side Nominal input voltage U_N: 110 VDC Input voltage range: 77 VDC ... 137.5 VDC Input voltage range in reference to U_N: 0.7 ... 1.25 Drive and function: monostable Drive (polarity): polarized Typical input current at U_N: 4.5 mA Typical response time: 5 ms Typical release time: 11 ms Coil voltage: 60 VDC Protective circuit: Bridge rectifier Surge protection; Freewheeling diode RCZ filter Wide-range electronics Operating voltage display: Yellow LED
Output data	Switching Contact switching type: 1changeover contact Type of switch contact: Single contact Contact material: AgNi Maximum switching voltage: 250 V AC/DC (Separating plate PLC-ATP must be installed for voltages larger than 250V (L1, L2, L3) between identical terminal blocks in adjacent modules.) Minimum switching voltage: 12 V (10mA) Limiting continuous current: 10 A (With inserted bridge 2967691) Maximum inrush current: 30 A (300ms) Min. switching current: 10 mA (12V) Interrupting rating (ohmic load) max.: 240 W (at 24 V DC) 58 W (at 48 V DC) 48 W (at 60 V DC) 50 W (at 110 V DC) 75 W (at 220 V DC) 2500 VA (for 250 V AC) Switching capacity: 2 A (24V (DC13)) 0.2 A (220 V (DC13)) 6 A (230 V (AC 15))
Connection data	Connection method: Push-in connection Stripping length: 10 mm Conductor cross section rigid: 0.14 mm² ... 2.5 mm² Conductor cross section flexible: 0.14 mm² ... 2.5 mm² 0.2 mm² ... 2.5 mm² (Single ferrule) 2x 0.5 mm² ... 1 mm² (TWIN ferrule) Conductor cross section AWG: 26 ... 14
Dimensions	Width: 14 mm Height: 80 mm Depth: 94 mm
Material specifications	Flammability rating according to UL 94: V0 (Housing)
Environmental and real-life conditions	Ambient conditions Degree of protection (Relay): RT III (Relay) Degree of protection (Relay base): IP20 (Relay base) Ambient temperature (operation): -40°C ... 70°C (Temperature class TX) Ambient temperature (storage/transport): -40°C ... 85°C
Approvals	CE Certificate: CE-compliant UKCA Certificate: UKCA-compliant Shipbuilding approval Certificate: TAE0000196 Corrosive gas test Identification: ISA-S71.04. G3 Harsh Group EN60068-2-60 DNV GL data Temperature: D Humidity: A Vibration: B/C EMC: B Enclosure: Required protection according to the Rules shall be provided upon installation on board
EMC data	Low Voltage Directive: Conformance with Low Voltage Directive Electromagnetic compatibility: Conformance with EMC directive
Standards and regulations	Standards/regulations: IEC 60947-5-1 EN50155 (VDE0115 part 200) EN61373 EN50121
Mounting	Mounting type: DIN rail mounting Assembly instructions: in rows with zero spacing Mounting position: any