2910502 PHOENIX CONTACT - Technology Bsa

PLC-RSC- 24DC/21-21/MS - Relay Module

PLC-INTERFACE, consisting of a relay base and pluggable power contact relay with manual operation, integrated status LED and freewheeling diode, Screw connection, 2 changeover contacts, Freewheeling diode, Input voltage: 24 VDC

Cod. Articolo: 2910502

Cod. Fornitore: 2910502

PHOENIX CONTACT

Product properties	Product type: Relay Module Product family: PLC-INTERFACE Application: Palm switch Operating mode: 100% operating factor Mechanical service life: 5x 10⁶cycles Insulation characteristics Insulation: Safe isolation: Control side / contact side Insulation characteristics: Standards/regulations Insulation: Safe isolation: Control side / contact side Overvoltage category: III Pollution degree: 2
Electrical properties	Maximum power dissipation for nominal condition: 0.44 W Test voltage (Winding/contact): 4 kV AC (50Hz, 1min., winding/contact) Test voltage (Changeover contact/changeover contact): 2.5 kV AC (50Hz, 1min., changeover contact/changeover contact) Standards/regulations Rated surge voltage: 6 kV
Input data	Coil side Nominal input voltage U_N: 24 VDC Input voltage range: 20.2 VDC ... 33.6 VDC (20°C) Drive and function: monostable Drive (polarity): polarized Typical input current at U_N: 18 mA Typical response time: 10 ms Typical release time: 10 ms Coil voltage: 24 VDC Protective circuit: Freewheeling diode; Freewheeling diode Operating voltage display: Yellow LED
Output data	Switching Contact switching type: 2 changeover contacts Type of switch contact: Single contact Contact material: AgNi Maximum switching voltage: 250 V AC/DC (The separating plate PLC-ATP should be installed for voltages larger than 250 V (L1, L2, L3) between identical terminal blocks in adjacent modules. Potential bridging is then carried out with FBST 8-PLC... or ...FBST 500...) Minimum switching voltage: 12 V (10mA) Limiting continuous current: 6 A Maximum inrush current: 12 A (20ms) Min. switching current: 10 mA (12V) Interrupting rating (ohmic load) max.: 192 W (24VDC) 62 W (48VDC) 42 W (60VDC) 55 W (110VDC) 66 W (220VDC) 2000 VA (250VAC) Switching capacity: 1 A (24V, DC13) 1.5 A (230 V, AC15)
Connection data	Connection method: Screw connection Stripping length: 8 mm Screw thread: M3 Conductor cross section rigid: 0.14 mm² ... 2.5 mm² Conductor cross section flexible: 0.14 mm² ... 2.5 mm² 0.2 mm² ... 2.5 mm² (Single ferrule) 2x 0.5 mm² ... 1.5 mm² (TWIN ferrule) Conductor cross section AWG: 26 ... 14 Tightening torque: 0.6 Nm ... 0.8 Nm
Dimensions	Width: 14 mm Height: 80 mm Depth: 104 mm
Material specifications	Flammability rating according to UL 94: V0 (Housing)
Environmental and real-life conditions	Ambient conditions Degree of protection (Relay): RT II (Relay) Degree of protection (Relay base): IP20 (Relay base) Degree of protection (Installation location): Ã¢¥ IP54 (Installation location) Ambient temperature (operation): -40°C ... 60°C Ambient temperature (storage/transport): -40°C ... 85°C Altitude: Ã¢¤ 2000 m
Approvals	CE Certificate: CE-compliant UKCA Certificate: UKCA-compliant UL, USA Identification: UL508 UL508 Recognized UL, USA/Canada Identification: UL508 UL508 Recognized Shipbuilding approval Certificate: TAE0000196 Corrosive gas test Identification: ISA-S71.04. G3 Harsh Group EN60068-2-60 DNV GL data Temperature: D Humidity: A Vibration: B/C EMC: B Enclosure: Required protection according to the Rules shall be provided upon installation on board
EMC data	Low Voltage Directive: Conformance with Low Voltage Directive Electromagnetic compatibility: Conformance with EMC directive
Standards and regulations	Standards/regulations Standards/regulations: EN50178
Mounting	Mounting type: DIN rail mounting Assembly instructions: in rows with zero spacing Mounting position: any