2910536 PHOENIX CONTACT - Technology Bsa

PLC-RSC- 24UC/2X21/FG - Relay Module

PLC-INTERFACE, consisting of a relay base and plug-in safety relay with force-guided contacts in accordance with DINEN61810-3, Screw connection, 2 changeover contacts, forcibly actuated, Bridge rectifier, Input voltage: 24 V AC/DC

Cod. Articolo: 2910536

Cod. Fornitore: 2910536

PHOENIX CONTACT

Product properties	Product type: Relay Module Product family: PLC-INTERFACE Application: Forcibly guided contacts Operating mode: 100% operating factor Mechanical service life: approx. 10⁷ cycles B_10d: 600000 Cycles (AC1; 250V/6A; 1 NO) 900000 Cycles (AC1; 250V/3A; 1NO) 1800000 Cycles (AC1; 250V/1,5A; 1NO) 180000 Cycles (AC15; 250V/3A; 1NO) 560000 Cycles (AC15; 250V/2A; 1NO) 4600000 Cycles (AC15; 250V/0,75A; 1NO) 360000 Cycles (DC13; 24V/3A; 1NO) 740000 Cycles (DC13; 24V/1,5A; 1NO) 4200000 Cycles (DC13; 24V/0,75A; 1NO) Insulation characteristics Insulation: Safe isolation, reinforced insulation Insulation characteristics: Standards/regulations Insulation: Safe isolation, reinforced insulation Overvoltage category: III Pollution degree: 2
Electrical properties	Maximum power dissipation for nominal condition: 0.72 W Test voltage (Winding/contact): 4 kV_rms (50Hz, 1min., winding/contact) Test voltage (Changeover contact/changeover contact): 2.5 kV_rms (50Hz, 1min., changeover contact/changeover contact) Standards/regulations Rated insulation voltage: 250 VAC Rated surge voltage: 6 kV
Input data	Coil side Nominal input voltage U_N: 24 V AC/DC Input voltage range: 20.9 V AC/DC ... 32.4 V AC/DC (20°C) Input voltage range in reference to U_N: see diagram Drive and function: monostable Drive (polarity): polarized Typical input current at U_N: 30 mA Typical response time: 3 ms ... 15 ms Typical release time range: 3 ms ... 15 ms Coil voltage: 24 VDC Protective circuit: Bridge rectifier Operating voltage display: Yellow LED
Output data	Switching Contact switching type: 2 changeover contacts, forcibly actuated Type of switch contact: Single contact Contact material: AgNi Maximum switching voltage: 250 V AC/DC Minimum switching voltage: 5 V (10mA) Limiting continuous current: 6 A Maximum inrush current: 6 A Min. switching current: 10 mA (5 V) Interrupting rating (ohmic load) max.: 144 W (24VDC) 288 W (48VDC) 88 W (110VDC) 110 W (220VDC) 1500 VA (250VAC) Switching capacity min.: 150 mW Switching capacity: 3 A (24V, DC13) 3 A (230 V, AC15) Force-guided contacts in accordance with EN61810-3: Type B
Connection data	Connection method: Screw connection Stripping length: 8 mm Screw thread: M3 Conductor cross section rigid: 0.14 mm² ... 2.5 mm² Conductor cross section flexible: 0.14 mm² ... 2.5 mm² 0.2 mm² ... 2.5 mm² (Single ferrule) 2x 0.5 mm² ... 1.5 mm² (TWIN ferrule) Conductor cross section AWG: 26 ... 14 Tightening torque: 0.6 Nm ... 0.8 Nm
Dimensions	Width: 14 mm Height: 80 mm Depth: 104 mm
Environmental and real-life conditions	Ambient conditions Degree of protection (Relay): RT II (Relay) Degree of protection (Relay base): IP20 (Relay base) Degree of protection (Installation location): Ã¢¥ IP54 (Installation location) Ambient temperature (operation): -20°C ... 60°C Ambient temperature (storage/transport): -20°C ... 85°C Altitude: Ã¢¤ 2000 m
Approvals	CE Certificate: CE-compliant UKCA Certificate: UKCA-compliant UL, USA Identification: UL508 UL508 Recognized UL, USA/Canada Identification: UL508 UL508 Recognized Shipbuilding approval Certificate: TAE0000196 Corrosive gas test Identification: ISA-S71.04. G3 Harsh Group EN60068-2-60 DNV GL data Temperature: D Humidity: A Vibration: B/C EMC: B Enclosure: Required protection according to the Rules shall be provided upon installation on board
EMC data	Low Voltage Directive: Conformance with Low Voltage Directive Electromagnetic compatibility: Conformance with EMC directive
Standards and regulations	Standards/regulations Standards/regulations: IEC 60947-5-1 DINEN61810-3
Mounting	Mounting type: DIN rail mounting Assembly instructions: in rows with zero spacing Mounting position: any