Non disponibile 
| Product properties | Product type: Relay Module Product family: PLC-INTERFACE Application: Output function Operating mode: 100% operating factor Mechanical service life: 3x 107 cycles Insulation characteristics: Air clearances and creepage distances between the power circuits Insulation: Basic insulation Overvoltage category: III Pollution degree: 2 |
| Electrical properties | Maximum power dissipation for nominal condition: 0.43 W Test voltage (Winding/contact): 4 kVrms (50Hz, 1min.) Test voltage (): 1 kVrms (50Hz, 1min.) Test voltage (N/O contact / N/O contact): 2.5 kVrms (50Hz, 1min.) Air clearances and creepage distances between the power circuits Rated insulation voltage: 250 VAC Rated surge voltage: 4 kV (Safe isolation, reinforced insulation, and 6 kV between input circuit and output contact current paths) |
| Input data | Coil side Nominal input voltage UN: 24 VDC Input voltage range: 20.2 VDC ... 33.6 VDC (20°C) Drive and function: monostable Drive (polarity): polarized Typical input current at UN: 18 mA Input power dissipation for UN: 0.43 W Typical response time: 8 ms Typical release time: 10 ms Protective circuit: Reverse polarity protection; Polarity protection diode Freewheeling diode; Freewheeling diode Operating voltage display: Yellow LED |
| Output data | Switching Contact switching type: 2 N/O contacts Type of switch contact: Single contact Contact material: AgNi Maximum switching voltage: 250 V AC/DC (The separating plate PLC-ATP should be installed for voltages larger than 250 V (L1, L2, L3) between identical terminal blocks in adjacent modules. Potential bridging is then carried out with FBST 8-PLC... or ...FBST 500...) Minimum switching voltage: 5 V (10mA) Limiting continuous current: 6 A Maximum inrush current: 25 A (20ms) Min. switching current: 10 mA (5V) Interrupting rating (ohmic load) max.: 144 W (24VDC) 96 W (48VDC) 60 W (at 60 V DC) 44 W (at 110 V DC) 60 W (at 220 V DC) 1500 VA (250VAC) Switching capacity min.: 50 mW Switching capacity: 2 A (24V (DC13)) 0.2 A (250V (DC-13)) 3 A (24V (AC15)) 3 A (120V (AC15)) 3 A (250V (AC15)) |
| Connection data | Connection method: Screw connection Stripping length: 8 mm Screw thread: M3 Conductor cross section rigid: 0.14 mm² ... 2.5 mm² Conductor cross section flexible: 0.14 mm² ... 2.5 mm² 0.2 mm² ... 2.5 mm² (Single ferrule) 2x 0.5 mm² ... 1.5 mm² (TWIN ferrule) Conductor cross section AWG: 26 ... 14 Tightening torque: 0.6 Nm ... 0.8 Nm |
| Dimensions | Width: 14 mm Height: 80 mm Depth: 94 mm |
| Material specifications | Flammability rating according to UL 94: V0 (Housing) |
| Environmental and real-life conditions | Ambient conditions Degree of protection (Relay): RT III Degree of protection (Relay base): IP20 Degree of protection (Installation location): ⤠IP54 Ambient temperature (operation): -40°C ... 70°C Ambient temperature (storage/transport): -40°C ... 85°C Altitude: ⤠2000 m |
| Approvals | CE Certificate: CE-compliant UKCA Certificate: UKCA-compliant Shipbuilding approval Certificate: TAE0000196 Corrosive gas test Identification: ISA-S71.04. G3 Harsh Group EN60068-2-60 DNV GL data Temperature: D Humidity: A Vibration: B/C EMC: B Enclosure: Required protection according to the Rules shall be provided upon installation on board |
| EMC data | Low Voltage Directive: Conformance with Low Voltage Directive Electromagnetic compatibility: Conformance with EMC directive |
| Standards and regulations | Standards/regulations Standards/regulations: IEC 61810-1 Air clearances and creepage distances between the power circuits Standards/regulations: IEC 60947-5-1 |
| Mounting | Mounting type: DIN rail mounting Assembly instructions: in rows with zero spacing Mounting position: any |
| ECLASS | ECLASS-11.0: 27371601 ECLASS-12.0: 27371601 ECLASS-13.0: 27371601 |
| ETIM | ETIM 9.0: EC001437 |
| UNSPSC | UNSPSC 21.0: 39122300 |
Di seguito alcuni articoli correlati a quello che stai vedendo
