Disponibile 
| Number of analogue outputs | 8 |
| Input, current | No |
| Input, voltage | No |
| Input, resistor | No |
| Input, resistance thermometer | No |
| Input, thermocouple | No |
| Output, current | Yes |
| Output, voltage | Yes |
| Analogue inputs configurable | No |
| Analogue outputs configurable | Yes |
| Type of electric connection | Screw-/spring clamp connection |
| Capacitive load, max | 1 üF (voltage mode only) |
| Inductive load, max | 1 mH (current mode only) |
| Module keying | Electronic keying via programming software |
| Scan time | Per group 0...3: 1 ms, Per group 0...7: 2 ms |
| Step response time to 63% of value | Voltage mode: 18 üs max, Current mode: 1 ms max |
| Module conversion method | R-Ladder DAC, monotonicity with no missing codes |
| Outputs | 8 voltage or current |
| Open circuit detection | Current mode only |
| Drive capability | Voltage: 1000 é minimum, Current: 500 é maximum |
| RTB torque | 5069-RTB18-SCREW RTB only: 0.4 Nm (3.5 lbin) |
| Overvoltage protection, max | ±32V DC |
| Short circuit detection | Voltage mode only â output electronically limited to 16 mA or less |
| Data format | IEEE 32-bit floating point |
| Wire category | 2 - shielded input ports, 2 - power ports, 1 wire per terminal for each signal port |
| Power dissipation, max | 5.3 W |
| Indicators | 1 green/red module status indicator, 8 yellow/red I/O status indicators |
| Thermal dissipation, max | 18.1 BTU/hr |
| Accuracy drift with temperature | Voltage: 0.30% full scale, Current: 0.50% full scale |
| Resolution | 16 bits across ±10.5V - 320 üV/bit, 16 bits across 10.5V - 160 üV/bit, 16 bits across 5.25V - 80 üV/bit, 16 bits across 21 mA - 320 nA/bit |
| Wire size | 5069-RTB18-SPRING removable terminal block: 0.5...1.5 mm² (22...16 AWG) solid or stranded copper wire rated at 105 °C (221 °F), or greater, 2.9 mm (0.11 in.), max diameter including insulation, 5069-RTB18-SCREW removable terminal block: 0.5...1.5 mm² (22. |
| Calibrated accuracy | Voltage: 0.10% full scale @ 25 °C Current: 0.10% full scale @ 25 °C |
| Suitable for safety functions | No |
| Repeatability | 0.05 % |
| Conversion time | Per channel: 25 µs |
| Output range, current | 0...20 mA, 4...20 mA |
| Output range, voltage | ±10V, 0...10V, 0...5V |
| Calibration methods | Factory calibrated, User-performed (optional) |
| Insulation stripping length | 5069-RTB18-SPRING connections: 10 mm (0.39 in.), 5069-RTB18-SCREW connections: 12 mm (0.47 in.) |
| Width | 22 mm |
| Height | 144.57 mm |
| Depth | 105.42 mm |
| Enclosure type | None (open-style) |
| Surrounding air temperature, max | 60 °C |
| North American temperature code | T4 |
| Operating temperature | 0 °C |
| Emissions | IEC 61000-6-4 |
| ESD immunity | 6 kV contact discharges, 8 kV air discharges |
| EFT/B immunity | ±4 kV @ 5 kHz on power ports, ±3 kV @ 5 kHz on shielded output ports |
| Relative humidity | 5...95% noncondensing |
| Conducted RF immunity | 10V rms with 1 kHz sine-wave 80% AM from 150 kHz...80 MHz |
| Surge transient immunity | ±1 kV line-line (DM) and ±2 kV line-earth (CM) on power ports, ±2 kV line-earth (CM) on shielded output ports |
| Radiated RF immunity | 10 V/m with 1 kHz sine-wave 80% AM from 80...2000 MHz, 10 V/m with 200 Hz 50% Pulse 100% AM @ 900 MHz, 10 V/m with 200 Hz 50% Pulse 100% AM @ 1890 MHz, 3 V/m with 1 kHz sine-wave 80% AM from 2000...2700 MHz |
| Nonoperating temperature | -40 °C |
| Voltage variation | 10 ms interruption on MOD power port |
| SA power | 250 mA @ 18...32V DC |
| SA power passthrough, max | 9.95 A @ 18...32V DC |
| MOD power | 75 mA @ 18...32V DC |
| MOD power passthrough, max | 9.55 A @ 18...32V DC |
| Analog output ratings | ±10V DC @ 0...20 mA per channel |
| RTB keying | None |
| Weight | 175 g |
| Vibration | 5 G @ 10...500 Hz |
| Shock | Operating: 30 G, Non operating: 50 G |
| Slot width | 1 |
| DIN rail | Compatible zinc-plated chromate-passivated steel DIN rail, You can use the EN50022 - 35 x 7.5 mm (1.38 x 0.30 in) DIN rail |
| Isolation voltage | 250V (continuous), basic insulation type, 50V Functional isolation between SA power and input ports, No isolation between individual input ports |
| ATEX temp code | T4 |
| IECEx temp code | T4 |
Di seguito alcuni articoli correlati a quello che stai vedendo
