1078803 PHOENIX CONTACT - Technology Bsa

RIF-1-RSC-LDP-12DC/1IC - Relay Module

Preassembled relay module with screw connection, consisting of: relay base, power contact relay, plug-in display/interference suppression module, retaining bracket. Contact switching type: 1 N/O contact, max. inrush current up to 130A peak, 80A (20ms), 12VDC input voltage

Product Code: 1078803

Partner cod.: 1078803

PHOENIX CONTACT

Notes	General: FBS 2-6... plug-in bridge for the input side (A2) and FBS-2-8... plug-in bridge for the output side (11/21)
Product properties	Product type: Relay Module Product family: RIFLINEcomplete Application: high inrush currents Operating mode: 100% operating factor Mechanical service life: 3x 10⁷ cycles Insulation characteristics Insulation: Safe isolation, reinforced insulation Insulation characteristics: Standards/regulations Insulation: Safe isolation, reinforced insulation Overvoltage category: III Pollution degree: 2
Electrical properties	Maximum power dissipation for nominal condition: 0.41 W Test voltage (Winding/contact): 4 kV AC (50Hz, 1min., winding/contact) Standards/regulations Rated insulation voltage: 250 VAC Rated surge voltage: 6 kV
Input data	Coil side Nominal input voltage U_N: 12 VDC Input voltage range: 9.6 VDC ... 16.8 VDC (20°C) Input voltage range in reference to U_N: see diagram Drive and function: monostable Drive (polarity): polarized Typical input current at U_N: 34 mA Typical response time: 8 ms Typical release time: 10 ms Coil voltage: 12 VDC Protective circuit: Surge protection; Freewheeling diode Operating voltage display: Yellow LED
Output data	Switching Contact switching type: 1 N/O contact Type of switch contact: Single contact Contact material: AgSnO Maximum switching voltage: 250 V AC/DC (The separating plate PLC-ATP should be installed for voltages larger than 250 V (L1, L2, L3) between identical terminal blocks in adjacent modules. Potential bridging is then carried out with FBST 8-PLC... or ...FBST 500...) Minimum switching voltage: 12 V (100 mA) Limiting continuous current: 6 A 10 A (Value is permissible if connections 11 and 21, as well as connections 14 and 24 are bridged.) Maximum inrush current: 80 A (20ms) 130 A (peak, at capacitive load, 230 V AC, 24 Ã¼F) Min. switching current: 100 mA (12VDC) Interrupting rating (ohmic load) max.: 264 W (at 24VDC, observe contact derating) 58 W (at 48 V DC) 48 W (at 60 V DC) 50 W (at 110 V DC) 80 W (at 220 V DC) 2750 VA (at 250VAC, observe contact derating) Switching capacity min.: 1200 mW Utilization category CB Scheme (IEC 60947-5-1): AC15, 6 A/250 V (N/O contact) DC13, 2 A/24 V (N/O contact)
Connection data	Connection method: Screw connection Stripping length: 8 mm Conductor cross section rigid: 0.5 mm² ... 4 mm² Conductor cross-section rigid (2 conductors with same cross section): 0.5 mm² ... 2.5 mm² Conductor cross section flexible: 0.5 mm² ... 4 mm² 0.5 mm² ... 4 mm² (Ferrule with plastic sleeve) Conductor cross section flexible (2 conductors with same cross section): 0.5 mm² ... 2.5 mm² 0.5 mm² ... 1.5 mm² (TWIN ferrule with plastic sleeve) Conductor cross section AWG: 20 ... 10 (solid) 20 ... 12 (flexible) Tightening torque: 0.5 Nm ... 0.6 Nm
Dimensions	Width: 16 mm Height: 90 mm Depth: 75 mm
Environmental and real-life conditions	Ambient conditions Degree of protection (Relay): RT II (Relay) Degree of protection (Relay base): IP20 (Relay base) Degree of protection (Installation location): Ã¢¥ IP54 (Installation location) Ambient temperature (operation): -40°C ... 70°C Ambient temperature (storage/transport): -40°C ... 85°C Altitude: Ã¢¤ 2000 m
Approvals	Corrosive gas test Identification: ISA-S71.04. G3 Harsh Group EN60068-2-60
Standards and regulations	Standards/regulations Standards/regulations: IEC 60947-5-1
Mounting	Mounting type: DIN rail mounting Assembly instructions: in rows with zero spacing Mounting position: any