Industrial Automation
Notes | Safety note Safety note: ⢠WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible. ⢠WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product. WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property. ⢠The products are suitable for applications in plant, controller, and electrical device engineering. ⢠Assembled products may not be manipulated or improperly opened. ⢠Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products). ⢠When using the product in direct connection with third-party manufacturers, the user is responsible. ⢠For operating voltages > 50V AC, conductive connector housings must be grounded ⢠Ensure that the protective or functional ground has been properly connected. ⢠Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product ⢠The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product. ⢠Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products ⢠The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12). ⢠Operate the connector only when it is fully plugged in and interlocked. ⢠Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards. ⢠Observe the minimum bending radius of the cable. Lay the cable without twisting it. |
Product properties | Product type: Connectors for energy storage Product family: BPC Number of positions: 1 Insulation characteristics Degree of pollution: 2 |
Electrical properties | Rated voltage (III/2): 1500 VDC Nominal voltage ATD: 1500 (III/2) in accordance with IEC 61984 1000 in accordance with UL4128 Rated current: 120 A (with 25mm² conductor cross-section, in accordance with IEC 61984) 76 A (with 16mm² conductor cross-section, in accordance with IEC 61984) 120 A (with AWG4, in accordance with UL4128) Contact resistance: ⤠5 mé Nominal voltage UN: 1000 V (in accordance with UL4128) |
Material specifications | Color: black Material: Polyamide Copper Silicon Flammability rating according to UL 94: V0 |
Cable/line | Single wire, cross section: 16 mm² 25 mm² Stripping length of the individual wire: 18 mm ±1mm Tightening torque, union nut: 3.00 Nm |
Mechanical properties | Mechanical data Insertion/withdrawal cycles: 100 Insertion force: ⤠75 N Withdrawal force: ⥠10 N |
Environmental and real-life conditions | Ambient conditions Degree of protection (when plugged in): IP65 (The panel is feed-through hole) Degree of protection (not plugged in): IP20 Degree of protection: IP65 Ambient temperature (operation): -40°C ... 70°C Ambient temperature (storage/transport): -40°C ... 70°C |
Standards and regulations | Standards/specifications: IEC 61984:2008 EN61984:2008 UL4128 PPP51090A |
Mounting | Assembly instructions: We recommend using the crimping dies and other crimping devices of Jiangsu Bozhiwang Automation Equipment Co., Ltd. for cable crimp connections; address: No. 39 Kun Lun Road, Xin Bei District, Changzhou, Jiangsu Province, China, email: flacz2020@163.com, die model: BZW-6F Connection method: Crimp |
ECLASS | ECLASS-11.0: 27440290 ECLASS-12.0: 27440290 ECLASS-13.0: 27440290 |
ETIM | ETIM 9.0: EC002943 |
UNSPSC | UNSPSC 21.0: 39121400 |
Description other products