Not available 
| Notes | Notes on operation: Repeated hard short circuits can reduce the melting integral of the integrated backup fuse. A suitable flyback diode must be used when switching inductive loads If the DIP switches are not covered by an adjacent module, the PLC-ATP partition plate must be used for ESD protection The device contains components that can be damaged or destroyed by electrostatic discharge. When handling the device, observe the necessary safety precautions against electrostatic discharge (ESD) according to EN 61340-5-1 and EN 61340-5-2. The PLC-ATP separating plate should be installed for safe isolation between adjacent modules Do not connect adjacent channels to SELV/ PELV and voltages dangerous to the touch. At least one functional insulation against adjacent modules is complied with in the support rail direction. If the application has higher requirements on the insulation (basic or reinforced insulation), then these must be realized through suitable measures (e. g., partition plates). Do not use to separate SELV / PELV circuits from other circuits, because safe isolation is not guaranteed. |
| Product properties | Product type: Relay Module Product family: PLC-INTERFACE Application: with integrated electronic circuit breaker Operating mode: 100% operating factor Data management status Article revision: 02 Insulation characteristics: Air clearances and creepage distances Insulation: Functional insulation Overvoltage category: I Pollution degree: 2 |
| Electrical properties | Maximum power dissipation for nominal condition: < 1.6 W Fuse: electronic |
| Input data | Operating voltage (UN): 24 V DC (UIn+ - UA2) Operating voltage range (DC): 19.2 V DC ... 30 V DC (UIn+ - UA2) Current consumption (In+): 12 mA Tripping current (IN): 1 A (adjustable) 2 A (adjustable) 3 A (adjustable) 4 A (adjustable) 5 A (adjustable) 6 A (preset) Measuring tolerance: ñ 15 % Power dissipation: 0.06 W (Without load, A1 low) 0.4 W (Without load, A1 high) < 1.6 W (Normal operation) Switching: Switching input A1 Nominal switch-on voltage: 24 V (UA1 - UA2) Switch-on voltage range: 11 V ... 30 V (UA1 - UA2) Switch-off voltage range: 0 V ... 2 V (UA1 - UA2) Current consumption (IA1): 4 mA (24 V) Switch-on time: 36 ms Switch-off time: 10 ms Switching frequency: ââ°¤ 2.5 Hz |
| Output data | Load circuit: Power MOSFET switching output (positive switching) Voltage drop: 0.16 V (6 A, UIn+ - Uout) Short-circuit switching capacity: 100 A DC 300 A DC (<5 short circuits) Required backup fuse: Only required if Imax of power supply unit > short-circuit switching capacity. Integrated failsafe element Fail-safe element: 15 A Surge voltage protection: > 33 V Max. capacitive load: 12000 õF (Depending on the current setting and the short-circuit current available) Shutdown time (): ââ°¤ 15 ms (Short circuit ââ°¥3 x IN) 0.1 s (Short circuit 2 ... <3 x IN) 1 s (Short circuit 1.5 ... <2 x IN) 4 s (Short circuit 1.1 ... <1.5 x IN) Undervoltage switch-off: ââ°¤ 17.8 V (active) ââ°¥ 19 V (inactive) Overvoltage switch-off: ââ°¥ 30.5 V (active) ââ°¤ 29.5 V (inactive) Waiting time: 5 s (Between the pulses) Number: 5 (Start attempts in hiccup mode) Signal: Feedback contact Output voltage: UIn+ - 0.7 V (high level) Current (Maximum current): ââ°¤ 20 mA State condition (Normal operation): low State condition (Error): high (Fuse has blown) State condition (Hiccup mode): high (After all 5 start attempts have been completed) |
| Connection data | Connection method: Screw connection Stripping length: 8 mm Conductor cross section rigid: 0.2 mm² ... 2.5 mm² Conductor cross-section rigid (2 conductors with same cross section): 0.14 mm² ... 1.5 mm² Conductor cross section flexible: 0.2 mm² ... 2.5 mm² 0.14 mm² ... 1.5 mm² Conductor cross section flexible (2 conductors with same cross section): 0.5 mm² ... 1.5 mm² (TWIN ferrule with plastic sleeve) Conductor cross section AWG: 30 ... 12 Tightening torque: 0.45 Nm ... 0.55 Nm (Usually these terminal blocks must be supported during conductor connection (held by one hand, supported on the housing)) |
| Dimensions | Item dimensions Width: 6.2 mm Height: 80 mm Depth: 94 mm |
| Environmental and real-life conditions | Ambient conditions Degree of protection: IP20 Degree of protection (Installation location): ââ°¥ IP54 Ambient temperature (operation): -25 °C ... 55 °C (Observe derating in the connected state) Ambient temperature (storage/transport): -40 °C ... 70 °C Altitude: ââ°¤ 2000 m (Without derating) ââ°¤ 3000 m (With correction factor for ambient temperature (operation) x 0.88) Permissible humidity (operation): 95 % |
| Approvals | UL, USA/Canada Identification: UL 2367 UL 60947-1 UL 60947-5-1 CSA C22.2 No. 60947-1 CSA C22.2 No. 60947-5-1 UL data Operating mode: Indoor use |
| Standards and regulations | Electromagnetic compatibility (EMC) Standards/regulations: EN 61000-6-2 EN 61000-6-3 Air clearances and creepage distances Standards/regulations: IEC 60664 |
| Mounting | Mounting type: DIN rail mounting Assembly note: in rows with zero spacing Mounting position: any |
Description other products
