Not available 
| Notes | General Note: LABS release ââ¬Ã¢ in accordance with test specification VW PV 3.10.7:2005-0 When connecting the conductor, make sure that the CAPAROC modules are not pulled apart due to tensile force. Gaps must not be created between the modules. |
| Product properties | Product type: Device circuit breakers Product family: CAPAROC Number of slots: 4 Data management status Article revision: 01 Insulation characteristics Protection class: III Pollution degree: 2 |
| Electrical properties | General Operating voltage: 10 V DC ... 30 V DC Rated voltage: 12 V DC 24 V DC Rated current IN: 45 A DC (Total current input) Rated surge voltage: 0.5 kV Tripping method: E (electronic) Feedback resistance: max. 35 V DC Dielectric strength: 35 V DC (Load circuit) Efficiency: > 99 % Closed circuit current I0: typ. 46 mA (no load at 24 V) Power dissipation: typ. 1.1 W (no load at 24 V) < 4.5 W (at 40 A) Temperature derating: 45 A (Total current at 60 °C) 20 A (Total current at 65 °C) 45 A (Total current at 35 °C, in accordance with UL) 40 A (Total current at 40 °C, in accordance with UL) 15 A (Total current at 50 °C, in accordance with UL) MTBF (IEC 61709, SN 29500): 7242508.37 h (at 25 °C with 21 % load) 3958056.77 h (at 40 °C with 34.25% load) 764697.81 h (at 60 °C with 100% load) Voltage drop: 0.082 V (at 40 A) Load circuit Undervoltage switch-off: ââ°¤ 9.2 V DC (active) ââ°¥ 10.2 V DC (inactive) Overvoltage switch-off: ââ°¥ 30.5 V DC (active) ââ°¤ 29.5 V DC (inactive) |
| Connection data | Main circuit IN+ Connection method: Push-in connection Stripping length: 18 mm Conductor cross section AWG: 20 ... 8 Conductor cross section, flexible, with ferrule, with plastic sleeve: 0.5 mm² ... 16 mm² Conductor cross section flexible, with ferrule without plastic sleeve: 0.5 mm² ... 16 mm² Main circuit IN- Connection method: Push-in connection Stripping length: 18 mm Conductor cross section AWG: 20 ... 8 Conductor cross section, flexible, with ferrule, with plastic sleeve: 0.5 mm² ... 16 mm² Conductor cross section flexible, with ferrule without plastic sleeve: 0.5 mm² ... 16 mm² System communication Connection method: Push-in connection Stripping length: 8 mm Conductor cross section rigid: 0.2 mm² ... 1.5 mm² Conductor cross section AWG: 24 ... 16 Conductor cross section, flexible, with ferrule, with plastic sleeve: 0.2 mm² ... 0.75 mm² Conductor cross section flexible, with ferrule without plastic sleeve: 0.2 mm² ... 1.5 mm² |
| Interfaces | EtherNet/IPâ⢠Maximum system extension: ââ°¤ 16 (CAPAROC modules alignable) Interface type: Ethernet Number: 2 Transmission speed: 10 Mbps 100 Mbps Transmission physics: Ethernet in RJ45 twisted pair Protocols supported: EtherNet/IPâ⢠|
| Signaling | Connection X1 LED green: lit (connect) Connection X1 LED yellow: lit (traffic) Connection X2 LED green: lit (connect) Connection X2 LED yellow: lit (traffic) Power (PWR) LED green: lit (Supply voltage within the operating voltage range) 3x flashing (Global programming lock deactivated) Power (PWR) LED red: lit (Supply voltage outside the operating voltage range) 5x flashing (Factory reset command accepted) Power (PWR) LED yellow: lit (PWR button pressed) 3x flashing (Global programming lock activated) NET LED off: off (No voltage present at the device or no IP address configured) NET LED green: lit (Communication with the controller present) flashing (IP address available, no communication with the controller) NET LED red: lit (Address Conflict Detection (ACD): ââ¬Ã Duplicate IP.â⬠Device has detected that its IP address is already in use in the network.) NET LED red-green: flashing (Device initialization self-test) MOD LED off: off (No supply voltage) MOD LED green: lit (Normal operation) flashing (The device is not yet configured) MOD LED red-green: flashing (Device initialization self-test) MOD LED red: lit (Error (EtherNet/IPââ¢: ââ¬Ã Major unrecoverable faultââ¬), e.g., program crash in the controller) flashing (Error (EtherNet/IPââ¢: ââ¬Ã Major recoverable faultââ¬), e.g., inconsistent or incorrect parameterization) Ready (RDY) LED yellow-green: flashing (Firmware installation running) Ready (RDY) LED yellow: lit (Firmware installation failed, perform manual voltage reset) Ready (RDY) LED green: lit (Firmware started successfully) |
| Dimensions | Dimensional drawing: https://caas.phoenixcontact.com/caas/v1/stable/media/49228/full/b1500?format=jpg Width: 24.8 mm Height: 132.4 mm Depth: 111.3 mm (incl. DIN rail 7.5 mm) |
| Material specifications | Color: light gray (RAL 7035) Material: PA 6 PC Flammability rating according to UL 94: V-0 |
| Environmental and real-life conditions | Ambient conditions Degree of protection: IP20 Ambient temperature (operation): -30 °C ... 65 °C Ambient temperature (storage/transport): -40 °C ... 70 °C Altitude: ââ°¤ 4000 m (amsl) Humidity test: 96 h, 95 % RH, 40 °C Shock (operation): 30g (11 ms period, half-sine shock pulse, according to IEC 60068-2-27) 25g (6 ms duration, half-sine shock pulse in accordance with IEC 60068-2-27, continuous shock) Vibration (operation): 5g (10 ... 150 Hz / 10 cycles / axis / X, Y, Z) |
| Approvals | UL approval Identification: UL/C-UL Listed UL 508 UL 121201 Class I, Division 2, Groups A, B, C, D, T4A |
| Standards and regulations | Standards/specifications: EN 61000-6-2 EN 61000-6-4 EN 61000-6-8 EN 60068-2-78 EN 50178 EN 60068-2-6 EN 60068-2-27 Note: EMC ââ¬Ã¢ Immunity for industrial areas EMC interference emission for professional devices that are used in business and commercial areas as well as in small businesses Environmental influences ââ¬Ã¢ Moisture and heat, constant Equipping power installations with electronic equipment Environmental influences ââ¬Ã¢ Vibrations (sinusoidal) Environmental influences ââ¬Ã¢ Shocks |
| Mounting | Mounting type: pluggable onto CAPAROC CRâ⬦ current rail |
Description other products
