Industrial Automation
Notes | General: The electrical and mechanical data specified assume that the connector pair is correctly locked and mounted. If the connector is unlocked and if there is a danger of contamination, the connector must be sealed using a protective cap > IP54. Influences arising from litz wires, cables or PCB assembly must also be taken into consideration. Safety note Safety note: WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property. ⢠WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible. ⢠WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product. ⢠The products are suitable for applications in plant, controller, and electrical device engineering. ⢠When operating the connectors in outdoor applications, they must be separately protected against environmental influences. ⢠Assembled products may not be manipulated or improperly opened. ⢠Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products). ⢠When using the product in direct connection with third-party manufacturers, the user is responsible. ⢠For operating voltages > 50V AC, conductive connector housings must be grounded ⢠Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards. ⢠Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product ⢠Only use tools recommended by PhoenixContact ⢠Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products ⢠Ensure that the protective or functional ground has been properly connected. ⢠VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector ⢠The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12). |
Mounting | Mounting type: Rear mounting M16 x 1.5 Connection method: Hybrid cable |
Product properties | Product type: Circular connectors (device side) Sensor type: Ethernet hybrid Number of positions: 8 No. of cable outlets: 1 Shielded: yes Coding: Y Thread type: M12 Insulation characteristics Overvoltage category: II Degree of pollution: 3 |
Material specifications | Material: Zinc die-cast (nickel-plated) Flammability rating according to UL 94: V0 Seal material: FKM Contact material: CuZn Contact surface material: Ni/Au Contact carrier material: PA 6.6 Material for screw connection: Brass, nickel-plated |
Electrical properties | Contact resistance: ⤠3 mé Insulation resistance: ⥠100 Mé Nominal voltage UN: 48 VAC (Power and data) 50 VDC (Power and data) Nominal current IN: 0.5 A (Data) 6 A (Power) Transmission medium: Copper Transmission characteristics (category): CAT5 |
Connection data | Conductor connection Connection method: Hybrid cable Contact connection type: Socket Tightening torque: 2 Nm 3 Nm |
Mechanical properties | Mechanical data Insertion/withdrawal cycles: ⥠100 |
Connector | Connection 1 Head design: Socket Head cable outlet: straight Head thread type: M12 Head locking type: SPEEDCON Coding: Y Connection 2 Head design: free cable end |
Cable/line | Cable length: 5 m Ethernet hybrid[94H] Cable weight: 87 kg/km UL AWM Style: 21815 (80°C/300 V) Number of positions: 8 Shielded: yes Cable type: Ethernet hybrid[94H] Conductor structure: 1x4xAWG26 + 1x4xAWG20 Conductor structure signal line: 19x 0.10 mm AWG signal line: 26 Conductor cross section: 4x 0.15 mm² (Data) 4x 0.6 mm² (Power) Wire diameter incl. insulation: 1.05 mm (Data) 1.4 mm (Power) External cable diameter: 7.6 mm ±0.2mm Outer sheath, material: PUR External sheath, color: black RAL9005 Conductor material: Bare Cu litz wires Material wire insulation: PP (Data) PP (Power) Single wire, color: white/orange, orange, white/green, green, white, blue, brown, black Overall twist: 1 star quad and 4 wires with 2 fillers Optical shield covering: 85 % Insulation resistance: ⥠5 Gé*km Loop resistance: ⤠280.00 é/km (Data) ⤠34.60 é/km (Power) Wave impedance: 100 é ±15é (4 MHz ... 100 MHz) Working capacitance: nom. 50 nF (per kilometer) Differential impedance: 100 é ±5% (at 100 MHz) Nominal voltage, cable: ⤠300 V (Peak value, not for high-power applications) Test voltage Core/Core: 2000 V (50Hz, 1min.) Test voltage Core/Shield: 2000 V (50Hz, 1min.) Minimum bending radius, fixed installation: 5 x D Minimum bending radius, flexible installation: 10 x D Max. bending cycles: 2000000 Tensile strength: 70 N (in accordance with DINEN50565-1 for flexible installation) 240 N (in accordance with DINEN50565-1 for fixed installation) Near end crosstalk attenuation (NEXT): 56.3 dB (at 4 ÃHz) 50.3 dB (at 10 MHz) 47.2 dB (at 16 MHz) 45.8 dB (at 20ÃHz) 42.9 dB (at 31.25ÃHz) 38.4 dB (at 62.5ÃHz) 35.3 dB (at 100 MHz) Shield attenuation: 6 dB (at 4 ÃHz) 9.5 dB (at 10 MHz) 12.1 dB (at 16 MHz) 13.5 dB (at 20ÃHz) 17.1 dB (at 31.25ÃHz) 24.8 dB (at 62.5ÃHz) 32 dB (at 100 MHz) ⥠80 dB (30 MHz ... 125 MHz) Halogen-free: according to IEC 60754 in accordance with DINVDE0472 part815 Flame resistance: in accordance with UL2556, Section9.1 and UL1581, Section1100 in accordance with UL2556, Section9.3 and UL1581, Section1060 Resistance to oil: in accordance with IEC 60811-404 According to DIN EN 50363-10-2 Other resistance: Low adhesion Special properties: Free of substances which would hinder coating with paint or varnish Silicone-free Ambient temperature (operation): -40°C ... 80°C (cable, fixed installation) -30°C ... 70°C (Cable, flexible installation) |
Environmental and real-life conditions | Ambient conditions Degree of protection: IP67 IP65/IP67 Ambient temperature (operation): -25°C ... 80°C (Plug / socket) -40°C ... 80°C (without mechanical actuation) |
Standards and regulations | M12 Standard designation: M12 connector Standards/specifications: IEC 61076-2-113 |
ECLASS | ECLASS-11.0: 27440102 ECLASS-12.0: 27440116 ECLASS-13.0: 27440103 |
ETIM | ETIM 9.0: EC003570 |
UNSPSC | UNSPSC 21.0: 39121400 |
Description other products