Not available 
| Input data | DC operation Input voltage: 24 VDC Nominal input voltage range: 100 VAC ... 240 VAC Input voltage range: 85 VAC ... 264 VAC (Derating < 90 V AC: 2.5%V) 100 VDC ... 350 VDC (UL508: 100 ... 250 V) Input voltage range AC: 85 VAC ... 264 VAC (Derating < 90 V AC: 2.5%V) Input voltage range DC: 100 VDC ... 350 VDC (UL508: 100 ... 250 V) Voltage type of supply voltage: AC/DC Inrush current: < 44 A (< 1.3 A2s) Inrush current integral (I2t): < 1.3 A2s AC frequency range: 45 Hz ... 65 Hz Frequency range DC: 0 Hz Mains buffering time: see diagram Buffer period: 20 min. (5A) Rotary selector switch: adjustable: 0.5 min; 1 min; 2 min; 3 min; 5 min; 10 min; 15 min; 20 min; PC-Mode Current consumption: 0.95 A (230 V AC) 1.1 A (230VAC, maximum) 1.7 A (120VAC) 1.8 A (120VAC, maximum) Protective circuit: Transient surge protection; Varistor Power factor (cos phi): approx. 0.5 Typical response time: 150 ms (230 V AC) 200 ms (120VAC) Input fuse: 6.3 A (slow-blow, internal) Permissible backup fuse: B6 B10 B16 Recommended breaker for input protection: 6 A ... 16 A (Characteristics B, C, D, K) |
| Output data | Efficiency: > 88 % (230 V AC, network operation) > 86 % (120VAC, network operation) > 86 % (Battery operation) Nominal output voltage: 24 VDC Setting range of the output voltage (USet): 22.5 VDC ... 29.5 VDC (Network operation; in the buffer mode, dependent on the battery voltage of 27.9 V DC ... 19.2 V DC) Nominal output current (IN): 5 A (-25°C...55°C) Output current limit: max. 6 A (Mains operation) Bridging time: 3600 s Derating: 55°C ... 70°C (2.5%/K) Feedback voltage resistance: 35 VDC Protection against overvoltage at the output (OVP): < 35 VDC Control deviation: < 1 % (change in load, static 10 % ... 90 %) Residual ripple: < 10 mVPP Output power: 120 W Nominal power: 120 W Peak switching voltages nominal load: < 25 mVPP Power dissipation: 16 W (230 V AC) 20 W (120VAC) 2 W (Maximum, no load) 4 W (Maximum, nominal load) Rise time: < 100 ms Connection in parallel: yes, 2 Connection in series: No Mains operation Nominal output voltage: 24 VDC Output voltage range: 22.5 VDC ... 29.5 VDC Nominal output current (IN): 5 A Battery operation Nominal output voltage: 24 VDC Output voltage range: 19.2 VDC ... 27.6 VDC (UOUT = UBAT - 0,5 V DC) Nominal output current (IN): 5 A Signal Output voltage: + 24 V Signal: Alarm Output description: Transistor switching output Maximum switching voltage: ⤠24 V Output voltage: 24 V Continuous load current: ⤠200 mA Signal: Battery charge Output description: Transistor switching output Maximum switching voltage: ⤠24 V Output voltage: 24 V Continuous load current: ⤠200 mA Signal: Battery mode Output description: Transistor switching output Maximum switching voltage: ⤠24 V Output voltage: 24 V Continuous load current: ⤠200 mA |
| Energy storage | End-of-charge voltage: 25 VDC ... 30 VDC (Default 27.6 V DC) Charging current: 1.5 A Deep discharge protection: 18 VDC ... 21 VDC (Default 19.2 V DC) Memory medium: external, battery 1.3Ah / 3.4Ah / 7.2Ah / 12Ah Battery presence check/time interval: 60 s Quality check of battery: 4 h ... 200 h (Default 12 h) Charge characteristic curve: I/U characteristic curve IQ technology: no Temperature compensation: 0 mV/K ... 200 mV/K (42 mV/K by default) Alarm signaling threshold: 18 VDC ... 30 VDC (Default 20.4 V DC) Network management: No |
| Connection data | Input Connection method: Screw connection Conductor cross section, rigid min.: 0.2 mm² Conductor cross section, rigid max.: 2.5 mm² Conductor cross section flexible min.: 0.2 mm² Conductor cross section flexible max.: 2.5 mm² Conductor cross section AWG min.: 24 Conductor cross section AWG max.: 12 Screw thread: M3 Tightening torque, min: 0.5 Nm Tightening torque max: 0.6 Nm Output Connection method: Screw connection Conductor cross section, rigid min.: 0.2 mm² Conductor cross section, rigid max.: 2.5 mm² Conductor cross section flexible min.: 0.2 mm² Conductor cross section flexible max.: 2.5 mm² Conductor cross section AWG min.: 24 Conductor cross section AWG max.: 12 Stripping length: 8 mm Screw thread: M3 Tightening torque, min: 0.5 Nm Tightening torque max: 0.6 Nm Signal Conductor cross section, rigid min.: 0.2 mm² Conductor cross section, rigid max.: 2.5 mm² Conductor cross section flexible min.: 0.2 mm² Conductor cross section flexible max.: 2.5 mm² Conductor cross section AWG min.: 24 Conductor cross section AWG max.: 12 Screw thread: M3 Tightening torque, min: 0.5 Nm Tightening torque max: 0.6 Nm |
| Interfaces | Interface: IFS (Interface system data port) |
| Signaling | Types of signaling: LED Signal output Status display: Green LED Note on status display: Mains voltage OK: Green LED, static at Signal output: Alarm Status display: Alarm Note on status display: Red LED, static at Signal output: Battery charge Status display: Battery (battery charge) is being charged Note on status display: Yellow LED, flashing Signal output: Battery mode Status display: Battery operation (Battery Mode) Note on status display: LED yellow, static at |
| Electrical properties | Insulation voltage input/output: 4 kV (type test) 2 kV (routine test) Insulation voltage output / PE: 500 VDC (routine test) Insulation voltage input / PE: 2 kV AC (type test) 2 kV AC (routine test) |
| Product properties | Product type: DC UPS IQ technology: no MTBF (IEC 61709, SN 29500): > 596000 h (40°C) Insulation characteristics Protection class: I Degree of pollution: 2 |
| Dimensions | Width: 60 mm Height: 130 mm Depth: 118 mm Installation dimensions Installation distance right/left: 0 mm / 0 mm Installation distance top/bottom: 50 mm / 50 mm |
| Mounting | Mounting type: DIN rail mounting Assembly instructions: alignable: horizontally 0mm, vertically 50mm Mounting position: horizontal DIN rail NS 35, EN 60715 |
| Material specifications | Housing material: Metal Aluminum (AlMg3) / sheet steel, zinc-plated Type of housing: Aluminum (AlMg3) + zinc-plated sheet steel, enclosed |
| Environmental and real-life conditions | Ambient conditions Degree of protection: IP20 Ambient temperature (operation): -25°C ... 70°C (> 55° C derating : 2.5%/K) Ambient temperature (storage/transport): -40°C ... 80°C Climatic class: 3K3 (in acc. with EN 60721) Max. permissible relative humidity (operation): 95 % (at 25°C, non-condensing) Shock: 18 ms, 30g, in each space direction (according to IEC 60068-2-27) Vibration (operation): < 15 Hz, amplitude ±2.5 mm (according to IEC 60068-2-6) 15 Hz ... 150 Hz, 2.3g, 90 min. |
| Standards and regulations | Rail applications: EN50121-4 Standard â Electronic equipment for use in electrical power installations and their assembly into electrical power installations: EN50178/VDE0160 (PELV) Standard â Limitation of mains harmonic currents: EN61000-3-2 Standard - Electrical safety: EN60950-1/VDE0805 (SELV) Standard â Protection against shock currents, basic requirements for protective separation in electrical equipment: EN50178 Standard â Safety extra-low voltage: EN60950-1 (SELV) EN60204 (PELV) Standard - Safe isolation: DINVDE0100-410 |
| Approvals | Shipbuilding approval: DNVGL(EMCB) UL approvals: UL/C-UL listed UL508 UL/C-UL Recognized UL60950-1 |
| EMC data | Low Voltage Directive: Conformance with Low Voltage Directive 2014/35/EC EMC requirements for noise emission: EN61000-6-3 EN61000-6-4 EMC requirements for noise immunity: EN61000-6-1 EN61000-6-2 Electromagnetic compatibility: Conformance with EMC Directive 2014/30/EU Noise emission: EN 55011 (EN 55022) Electrostatic discharge Standards/regulations: EN61000-4-2 Housing: Level 3 Electrostatic dischargeâ Contact discharge: 6 kV Discharge in air: 8 kV Comments: Criterion B Electromagnetic HF field Standards/regulations: EN61000-4-3 Electromagnetic HF fieldâ Frequency range: 80 MHz ... 2 GHz Test field strength: 10 V/m Comments: Criterion A Fast transients (burst) Standards/regulations: EN61000-4-4 Fast transients (burst)â Input: 4 kV (level 4 - asymmetrical: conductor to ground) Output: 2 kV (level 4 - asymmetrical: conductor to ground) Signal: 1 kV (level 4 - asymmetrical: conductor to ground) Comments: Criterion B Surge voltage load (surge) Standards/regulations: EN61000-4-5 Conducted interference Standards/regulations: EN61000-4-6 Conducted interferenceâ I/O/S: Level 3 Frequency range: 10 kHz ... 80 MHz Comments: Criterion A Voltage: 10 V Voltage dips Standards/regulations: EN61000-4-11 Emitted interference Standards/regulations: EN61000-6-3 Radio interference voltage in acc. with EN 55011: EN55011 (EN55022) ClassB, area of application: Industry and residential Emitted radio interference in acc. with EN 55011: EN 55011 (EN 55022) Class B, area of application: Industry and residential |
| ECLASS | ECLASS-11.0: 27040705 ECLASS-12.0: 27040705 ECLASS-13.0: 27040705 |
| ETIM | ETIM 9.0: EC000382 |
| UNSPSC | UNSPSC 21.0: 39121000 |
Description other products
