2866734 PHOENIX CONTACT - Technology Bsa

Input data	AC operation Nominal input voltage range: 3x 400 VÃAC ... 500 VÃAC Input voltage range: 3x 320 VÃAC ... 575 VÃAC 2x 360 VÃAC ... 575 VÃAC 450 VÃDC ... 800 VÃDC Voltage type of supply voltage: AC/DC Inrush current: < 15 A (typical) Inrush current integral (I²t): < 1 A²s AC frequency range: 45 Hz ... 65 Hz Frequency range DC: 0 Hz Mains buffering time: > 20 ms (400ÃVÃAC) > 30 ms (500 VÃAC) Current consumption: 3x 0.8 A (400ÃVÃAC) 3x 0.7 A (500 VÃAC) 0.2 A (600 VÃDC) Nominal power consumption: 268 VA Protective circuit: Transient surge protection; Varistor, gas-filled surge arrester Power factor (cos phi): 0.5 Typical response time: < 0.06 s Permissible backup fuse: B6 B10 B16 AC: Permissible DC backup fuse: DC: Connect a suitable fuse upstream Recommended breaker for input protection: 6 A ... 16 A (AC: Characteristics B, C, D, K) Discharge current to PE: < 3.5 mA
Output data	Efficiency: > 89 % (at 400 V AC and nominal values) Output characteristic: U/I Nominal output voltage: 24 VÃDC Ã±1Ã% Setting range of the output voltage (U_Set): 18 VÃDC ... 29.5 VÃDC (> 24 VÃDC, constant capacity restricted) Nominal output current (I_N): 5 A (-25Ã°CÃ...Ã60Ã°C, U_OUT =Ã24ÃVÃDC) POWER BOOST (I_Boost): 7.5 A (-25Ã°CÃ...Ã40Ã°C permanent, U_OUT = 24ÃVÃDC ) Selective Fuse Breaking (I_SFB): 30 A (12Ãms) Magnetic circuit breaker tripping: B2 / B4 / C2 Derating: 60°C ... 70°C (2.5%/K) Feedback voltage resistance: max. 35 VÃDC Protection against overvoltage at the output (OVP): < 35 VÃDC Residual ripple: < 20 mV_PP (with nominal values) Output power: 120 W Peak switching voltages nominal load: < 20 mV_PP (at nominal values, 20 MHz) Maximum no-load power dissipation: 4 W Power loss nominal load max.: 14 W Rise time: < 0.04 s (U_OUT (10 % ... 90 %)) Connection in parallel: yes, for redundancy and increased capacity Connection in series: yes Signal: DC OK active Output description: U_OUT > 0.9 x U_N: High signal Switching voltage range: 18 VÃDC ... 24 VÃDC Maximum inrush current: Ã¢Ã¢°¤ 20 mA (short-circuit-proof) Continuous load current: Ã¢Ã¢°¤ 20 mA Signal: DC OK floating Output description: Relay contact, U_OUT > 0.9 x U_N: Contact closed Maximum switching voltage: 30 V AC/DC 24 VÃDC Maximum inrush current: 0.5 A 1 A Continuous load current: Ã¢Ã¢°¤ 1 A Signal: POWER BOOST, active Output description: I_OUT < I_N: High signal Switching voltage range: 18 VÃDC ... 24 VÃDC Output voltage: + 24 VÃDC Maximum inrush current: Ã¢Ã¢°¤ 20 mA (short-circuit-proof) Continuous load current: Ã¢Ã¢°¤ 20 mA
Connection data	Input Connection method: Pluggable screw connection Conductor cross section, rigid min.: 0.2 mm² Conductor cross section, rigid max.: 2.5 mm² Conductor cross section flexible min.: 0.2 mm² Conductor cross section flexible max.: 2.5 mm² Conductor cross section AWG min.: 20 Conductor cross section AWG max.: 12 Stripping length: 7 mm Screw thread: M3 Tightening torque, min: 0.5 Nm Tightening torque max: 0.6 Nm Output Connection method: Pluggable screw connection Conductor cross section, rigid min.: 0.2 mm² Conductor cross section, rigid max.: 2.5 mm² Conductor cross section flexible min.: 0.2 mm² Conductor cross section flexible max.: 2.5 mm² Conductor cross section AWG min.: 20 Conductor cross section AWG max.: 12 Stripping length: 7 mm Screw thread: M3 Tightening torque, min: 0.5 Nm Tightening torque max: 0.6 Nm Signal Connection method: Pluggable screw connection Conductor cross section, rigid min.: 0.2 mm² Conductor cross section, rigid max.: 2.5 mm² Conductor cross section flexible min.: 0.2 mm² Conductor cross section flexible max.: 2.5 mm² Conductor cross section AWG min.: 20 Conductor cross section AWG max.: 12 Screw thread: M3 Tightening torque, min: 0.5 Nm Tightening torque max: 0.6 Nm
Signaling	Types of signaling: LED Active switching output Relay contact Operating voltage display: Green LED Signal output: DC OK active Status display: U_OUT > 0.9 x U_N: "DC OK" LED green Note on status display: U_OUT < 0.9 x U_N: Flashing "DC OK" LED Signal output: DC OK floating Status display: U_OUT > 0.9 x U_N: "DC OK" LED green Note on status display: U_OUT < 0.9 x U_N: Flashing "DC OK" LED Signal output: POWER BOOST, active Status display: I_OUT > I_N: LED "BOOST" yellow
Electrical properties	Number of phases: 3.00 Insulation voltage input/output: 4 kV AC (type test) 2 kV AC (routine test) Insulation voltage output / PE: 500 VÃDC (routine test) Insulation voltage input / PE: 3.5 kV AC (type test) 2 kV AC (routine test)
Product properties	Product type: Power supply Product family: QUINT POWER MTBF (IEC 61709, SN 29500): > 1290000 h (25Ã°C) > 680000 h (40Ã°C) > 290000 h (60Ã°C) Insulation characteristics Protection class: I Degree of pollution: 2
Dimensions	Width: 40 mm Height: 130 mm Depth: 125 mm Alternative assembly Width: 122 mm Height: 130 mm Depth: 43 mm
Mounting	Assembly instructions: alignable: P_N Ã¢Ã¢°¥50%, 5Ãmm horizontally, 15Ãmm next to active components, 50Ãmm vertically alignable: P_N <50%, 0Ãmm horizontally, 40Ãmm vertically top, 20 mm vertically bottom Mounting position: horizontal DIN rail NS 35, EN 60715 With protective coating: No
Material specifications	Housing material: Metal Hood version: Galvanized sheet steel, free from chrome (VI) Side element version: Aluminum
Environmental and real-life conditions	Ambient conditions Degree of protection: IP20 Ambient temperature (operation): -25°C ... 70°C (>Ã60Ã°C Derating: 2,5Ã%/K) Ambient temperature (storage/transport): -40°C ... 85°C Ambient temperature (start-up type tested): -40°C Maximum altitude: 5000 m Climatic class: 3K3 (in acc. with EN 60721) Max. permissible relative humidity (operation): Ã¢Ã¢°¤ 95 % (at 25°C, non-condensing) Shock: 18 ms, 30g, in each space direction (according to IEC 60068-2-27) Vibration (operation): < 15 Hz, amplitude Ã±2.5 mm (according to IEC 60068-2-6) 15 Hz ... 150 Hz, 2.3g, 90 min.
Standards and regulations	Rail applications: ENÃ50121-4 ENÃ50121-3-2 Standard Ã¢Ã¢¬Ã¢ Limitation of mains harmonic currents: ENÃ61000-3-2 Standard - Electrical safety: IEC 61010-2-201Ã(SELV) Standard - Equipment safety: GS (tested safety) Standard - Approval for medical use: IEC 60601-1, 2ÃxÃMOOP Standard Ã¢Ã¢¬Ã¢ Protection against shock currents, basic requirements for protective separation in electrical equipment: ENÃ50178 Standard Ã¢Ã¢¬Ã¢ Safety extra-low voltage: IEC 61010-1 (SELV) IEC 61010-2-201 (PELV) Standard - Safe isolation: IEC 61010-2-201 Standard - safety for equipment for measurement, control, and laboratory use: IEC 61010-1 Standard - surge resistance: VDEÃ0160 (curve W2) Approval - requirement of the semiconductor industry with regard to mains voltage dips: SEMI F47-0706 Compliance Certificate Overvoltage category EN 62477-1: III
Approvals	CSA: CAN/CSA-C22.2 No.Ã60950-1-07 CSA-C22.2 No.Ã107.1-01 Shipbuilding approval: DNVÃGLÃ(EMCÃA), ABS, LR, RINA, NK, BV UL approvals: UL Listed ULÃ508 UL/C-UL Recognized ULÃ60950-1 (3-wire + PE, star net) UL ANSI/ISA-12.12.01 Class I, Division 2, Groups A, B, C, D (Hazardous Location)
EMC data	Low Voltage Directive: Conformance with Low Voltage Directive 2014/35/EC EMC requirements for noise emission: ENÃ61000-6-3 ENÃ61000-6-4 EMC requirements for noise immunity: ENÃ61000-6-1 ENÃ61000-6-2 Electromagnetic compatibility: Conformance with EMC Directive 2014/30/EU Electrostatic discharge Standards/regulations: ENÃ61000-4-2 Electrostatic dischargeÃ¢Ã¢¬Ã¢¹ Contact discharge: 8 kV (Test Level 4) Discharge in air: 15 kV (Test Level 4) Comments: Criterion A Electromagnetic HF field Standards/regulations: ENÃ61000-4-3 Electromagnetic HF fieldÃ¢Ã¢¬Ã¢¹ Frequency range: 80 MHz ... 1 GHz 1 GHz ... 2 GHz 2 GHz ... 3 GHz Test field strength: 20 V/m (Test Level 3) 10 V/m (Test Level 3) 10 V/m (Test Level 3) Comments: Criterion A Fast transients (burst) Standards/regulations: ENÃ61000-4-4 Fast transients (burst)Ã¢Ã¢¬Ã¢¹ Input: 4 kV (Test Level 4 - asymmetrical) Output: 2 kV (Test Level 3 - asymmetrical) Signal: 2 kV (Test Level 4 - asymmetrical) Comments: Criterion A Surge voltage load (surge) Standards/regulations: ENÃ61000-4-5 Input: 2 kV (Test Level 3 - symmetrical) 4 kV (Test Level 4 - asymmetrical) Output: 1 kV (Test Level 2 - symmetrical) 2 kV (Test Level 3 - asymmetrical) Signal: 1 kV (Test Level 2 - asymmetrical) Comments: Criterion B Conducted interference Standards/regulations: ENÃ61000-4-6 Conducted interferenceÃ¢Ã¢¬Ã¢¹ I/O/S: asymmetrical Frequency range: 0.15 MHz ... 80 MHz Comments: Criterion A Voltage: 10 V (Test Level 3) Emitted interference Standards/regulations: ENÃ61000-6-3 Radio interference voltage in acc. with EN 55011: ENÃ55011 (ENÃ55022) ClassÃB, area of application: Industry and residential Emitted radio interference in acc. with EN 55011: EN 55011 (EN 55022) Class B, area of application: Industry and residential Criteria Criterion A: Normal operating behavior within the specified limits. Criterion B: Temporary impairment to operational behavior that is corrected by the device itself.