2900068 PHOENIX CONTACT - Technology Bsa

UM- D37SUB/M/HC3/16DO/MR/MT - Active module

16-channel relay module (1 changeover contact) for Honeywell C300 output modules. On the control side, the module is controlled via D-SUB 37-pos. or FLK 50-pos. A screw connection with knife disconnection is available on the field side.

Product Code: 2900068

Partner cod.: 2900068

PHOENIX CONTACT

Product properties	Product type: Interface module No. of channels: 16 Operating mode: 100% operating factor Mechanical service life: 2x 10⁷ cycles Insulation characteristics Insulation: Reinforced insulation Insulation characteristics: Air clearances and creepage distances, input/output Insulation: Reinforced insulation Overvoltage category: III Pollution degree: 2 Insulation characteristics: Air and creepage distances, output/output Insulation: Basic insulation Overvoltage category: III Pollution degree: 2
Electrical properties	No. of channels: 16 Air clearances and creepage distances, input/output Rated insulation voltage: 300 V Rated surge voltage: 6 kV (1.2/50 Ã¼s) Air and creepage distances, output/output Rated insulation voltage: 300 V Rated surge voltage: 4 kV (1.2/50 Ã¼s) Supported controller HONEYWELL Experion PKS C300/C-Series Suitable I/O card: TDOB01 (non-redundant) TDOB11 (redundant)
Input data	Nominal input voltage U_N: 24 VDC Input voltage range in reference to U_N: 0.85 ... 1.1 Input voltage range: 20.4 VDC ... 26.4 VDC Typical input current at U_N: 9 mA Typical response time: 5 ms Typical release time: 7 ms Protective circuit: Freewheeling diode Status display/channel: Yellow LED
Output data	Switching Contact switching type: 1changeover contact Type of switch contact: Single contact Contact material: AgSnO Maximum switching voltage: 250 V AC/DC Minimum switching voltage: 12 V AC/DC Limiting continuous current: 4 A (see derating curve) Min. switching current: 10 mA Interrupting rating (ohmic load) max.: 96 W (at 24 V DC) 20 W (at 48 V DC) 18 W (at 60 V DC) 23 W (at 110 V DC) 40 W (at 220 V DC) 1000 VA (for 250 V AC)
Connection data	Controller level Connection method: D-SUB pin strip Number of connections: 1 Number of positions: 37 Field level Connection method: Screw connection with disconnect knife Stripping length: 8 mm Screw thread: M3 Conductor cross section rigid: 0.2 mm² ... 4 mm² Conductor cross section flexible: 0.2 mm² ... 2.5 mm² Conductor cross section AWG: 24 ... 12 Control side Connection method: Flat-ribbon cable connector in acc. with IEC 60603-13 Number of connections: 1 Number of positions: 50
Signaling	Status display present: Yes
Dimensions	Width: 259 mm Height: 126 mm Depth: 66 mm
Environmental and real-life conditions	Ambient conditions Degree of protection: IP00 Degree of protection (Installation location): Ã¢¥ IP54 (Installation location) Ambient temperature (operation): -15°C ... 50°C Ambient temperature (storage/transport): -15°C ... 50°C Altitude: Ã¢¤ 2000 m
Standards and regulations	Air clearances and creepage distances, input/output Standards/regulations: EN61010-2-201 Air and creepage distances, output/output Standards/regulations: EN61010-2-201
Mounting	Mounting type: DIN rail mounting Assembly instructions: in rows with zero spacing Mounting position: any
Notes	General: Do not connect adjacent channels to SELV/ PELV and voltages dangerous to the touch. The outputs are not suitable for switching different outer conductors. Against adjacent modules in the support rail direction at least one functional insulation on the output-side is complied with. If the application has higher requirements on the insulation (basic insulation or reinforced insulation), then these must be realized through suitable measures (e.g. partition plates). For proper use, the specifications of the installation directive (see Downloads) must be observed. For applications or use with third-party products, the specifications, and the safety and warning instructions of the respective third-party manufacturer must also be met.