2901431 PHOENIX CONTACT - Technology Bsa

PSR-SPP-230AC/ESAM2/3X1/1X2/B - Safety relays

Safety relay for emergency stop and safety door up to SIL1, Cat.1, PLc, depending on the application up to SIL3, Cat.4, PLe, single-channel operation, 3 enabling current paths, nominal input voltage of 230V AC/DC, pluggable Push-in terminal block

Product Code: 2901431

Partner cod.: 2901431

PHOENIX CONTACT

Product properties	Product type: Safety relays Product family: PSRclassic Application: Emergency stop Safety door Mechanical service life: approx. 10⁷ cycles Relay type: Electromechanical relay with force-guided contacts in accordance with IEC/EN61810-3
Electrical properties	Maximum power dissipation for nominal condition: 2.88 W Nominal operating mode: 100% operating factor Air clearances and creepage distances between the power circuits Rated insulation voltage: 250 VAC Rated surge voltage/insulation: 4 kV / basic insulation (safe isolation, reinforced insulation, and 6 kV between A1-A2/logic/enabling and signaling current paths)
Input data	General Rated control circuit supply voltage U_S: 230 VAC -15% / +10% Rated control supply current I_S: 22 mA Voltage at input/start and feedback circuit: ~ 24 VDC Typical response time: 50 ms (manual start) 300 ms (automatic start) Typ. starting time with U_s: 300 ms (when controlled via A1 or S11/S12) Typical release time: 20 ms (when controlled via S11/S12) 150 ms (when controlled via A1) Recovery time: 1 s Maximum switching frequency: 0.5 Hz Protective circuit: Surge protection; Suppressor diode Surge protection; Varistor Max. permissible overall conductor resistance: 50 Ã©
Output data	Contact switching type: 3 enabling current paths 1 signaling current path Contact material: AgSnO₂, gold-flashed Maximum switching voltage: 250 V AC/DC Minimum switching voltage: 10 V AC/DC Limiting continuous current: 6 A (Enabling current paths) 5 A (Signaling current path) Maximum inrush current: 6 A Inrush current, minimum: 10 mA Sq. Total current: 72 A² Interrupting rating (ohmic load) max.: 144 W (at 24 V DC) 230 W (at 48 V DC) 68 W (at 110 V DC) 88 W (at 220 V DC) 2000 VA (for 250 V AC) Maximum interrupting rating (inductive load): 48 W (at 24 V DC) 40 W (at 48 V DC) 35 W (at 110 V DC) 33 W (at 220 V DC) Switching capacity min.: 100 mW Switching capacity (360/h cycles): 6 A (24VDC) 5 A (230 V AC) Switching capacity (3600/h cycles): 3 A (24V (DC13)) 3 A (230 V (AC 15)) Output fuse: 10 A gL/gG NEOZED (Enabling current paths) 6 A gL/gG NEOZED (Signaling current paths)
Connection data	Connection technology pluggable: yes Conductor connection Connection method: Push-in connection Conductor cross section rigid: 0.2 mm² ... 1.5 mm² Conductor cross section flexible: 0.2 mm² ... 1.5 mm² Conductor cross section, flexible, with ferrule, with plastic sleeve: 0.25 mm² ... 1.5 mm² (only together with CRIMPFOX 6) Conductor cross section flexible, with ferrule without plastic sleeve: 0.25 mm² ... 1.5 mm² (only together with CRIMPFOX 6) Conductor cross-section AWG: 24 ... 16 Stripping length: 8 mm
Signaling	Status display: 2 x green LEDs Operating voltage display: 1 x green LED
Dimensions	Width: 22.5 mm Height: 112 mm Depth: 114.5 mm
Material specifications	Housing material: Polyamide
Characteristics	Safety data Stop category: 0 Safety data: ENISO13849 Category: 1 (up to Cat. 4 depending on the application) Performance level (PL): c (up to PLe depending on the application) Safety dataÃ¢ Safety Integrity Level (SIL): 1 (up to SIL3 depending on the application) Safety dataÃ¢Ã¢ Safety Integrity Level (SIL): 1 (up to SIL3 depending on the application) Safety dataÃ¢Ã¢Ã¢ Safety Integrity Level (SIL): 1 (up to SIL3 depending on the application)
Environmental and real-life conditions	Ambient conditions Degree of protection: IP20 Min. degree of protection of inst. location: IP54 Ambient temperature (operation): -25°C ... 55°C Ambient temperature (storage/transport): -40°C ... 85°C Maximum altitude: Ã¢¤ 2000 m (Above sea level) Max. permissible humidity (storage/transport): 75 % (on average, 85% infrequently, non-condensing) Max. permissible relative humidity (operation): 75 % (on average, 85% infrequently, non-condensing) Shock: 15g Vibration (operation): 10Hz...150Hz, 2g
Approvals	Conformity/Approvals Conformance: CE-compliant
Standards and regulations	Air clearances and creepage distances between the power circuits Standards/regulations: IEC 60664-1
Mounting	Mounting type: DIN rail mounting Mounting position: any Connection method: Push-in connection