| Product properties | Product type: Safety relays
Product family: PSRclassic
Application: Emergency stop
Safety door
Light grid
Mechanical service life: 10x 106 cycles
Relay type: Electromechanical relay with force-guided contacts in accordance with IEC/EN61810-3
|
| Electrical properties | Maximum power dissipation for nominal condition: 3.6 W
Nominal operating mode: 100% operating factor
Air clearances and creepage distances between the power circuits
Rated insulation voltage: 250 VAC
Rated surge voltage/insulation: Basic insulation 4kV:
between all current paths and housing
Safe isolation, reinforced insulation 6kV:
between 13/14, 23/24, 33/34, and the remaining current paths
between 13/14, 23/24, 33/34 among one another
Supply
Rated control circuit supply voltage US: 20.4 VDC ... 26.4 VDC
24 VDC -15% / +10%
|
| Input data | General
Power consumption at US: typ. 3.6 W
Rated control supply current IS: typ. 150 mA
Inrush current: 200 mA (at US)
< 40 mA (with Us/Ix to S10)
< 150 mA (with Us/Ix to S12)
> -60 mA (with Us/Ix to S22)
< 40 mA (with Us/Ix to S34)
< 40 mA (with Us/Ix to S35)
Current consumption: < 40 mA (with Us/Ix to S10)
< 40 mA (with Us/Ix to S12)
> -40 mA (with Us/Ix to S22)
0 mA (with Us/Ix to S34)
< 5 mA (with Us/Ix to S35)
Voltage at input/start and feedback circuit: 24 VDC -15% / +10%
Filter time: 1 ms (at A1 in the event of voltage dips at Us)
max. 1.5 ms (at S10, S12; test pulse width)
7.5 ms (at S10, S12; test pulse rate)
Test pulse rate=5xTest pulse width
Typical response time: < 600 ms (automatic start)
< 70 ms (manual start)
Typ. starting time with Us: < 600 ms (when controlled via A1)
Typical release time: < 20 ms (when controlled via S11/S12 and S21/S22)
< 20 ms (when controlled via A1)
Concurrence: â
Recovery time: < 1 s
Delay time: K3(t), K4(t) fixed depending on model
Maximum switching frequency: 0.5 Hz
Protective circuit: Surge protection; Suppressor diode
Max. permissible overall conductor resistance: approx. 11 é (Input and start circuits at US)
Operating voltage display: 1 x green LED
Status display: 4 x green LEDs
|
| Output data | Contact switching type: 5 enabling current paths
1 signaling current path
Contact material: AgSnO2
Maximum switching voltage: 250 V AC/DC (Observe the load curve)
Minimum switching voltage: 5 V AC/DC
Limiting continuous current: 6 A (N/O contact, pay attention to the derating)
6 A (N/C contact)
Maximum inrush current: 20 A (Ãtï£100ms, undelayed contacts)
8 A (delayed contacts)
Inrush current, minimum: 10 mA
Sq. Total current: 55 A2 (observe derating)
Interrupting rating (ohmic load) max.: 144 W (24 V DC, Ã = 0 ms)
288 W (48 V DC, Ã = 0 ms)
110 W (110 V DC, Ã = 0 ms, delayed contacts: 77W)
88 W (220 V DC, Ã = 0 ms)
1500 VA (250 V AC, Ã = 0 ms, delayed contacts: 2000VA)
Maximum interrupting rating (inductive load): 42 W (24 V DC, Ã = 40 ms, delayed contacts: 48W)
42 W (48 V DC, Ã = 40 ms, delayed contacts: 40W)
42 W (110 V DC, Ã = 40 ms, delayed contacts: 35W)
42 W (220 V DC, Ã = 40 ms, delayed contacts: 33W)
Switching capacity min.: 50 mW
Switching capacity (360/h cycles): 4 A (24VDC)
4 A (230 V AC)
Switching capacity (3600/h cycles): 2.5 A (24V (DC13))
3 A (230 V (AC15))
Output fuse: 10 A gL/gG (N/O contact)
6 A gL/gG (N/C contact)
|
| Connection data | Connection technology
pluggable: yes
Conductor connection
Connection method: Push-in connection
Conductor cross section rigid: 0.2 mm² ... 1.5 mm²
Conductor cross section flexible: 0.2 mm² ... 1.5 mm²
Conductor cross section, flexible, with ferrule, with plastic sleeve: 0.25 mm² ... 1.5 mm² (only together with CRIMPFOX 6)
Conductor cross section flexible, with ferrule without plastic sleeve: 0.25 mm² ... 1.5 mm² (only together with CRIMPFOX 6)
Conductor cross-section AWG: 24 ... 16
Stripping length: 8 mm
|
| Dimensions | Width: 45 mm
Height: 112 mm
Depth: 114.5 mm
|
| Material specifications | Housing material: Polyamide
|
| Characteristics | Safety data
Stop category: 0
1
Safety data: ENISO13849
Category: 4 (Undelayed contacts)
3 (delayed contacts)
Performance level (PL): e (for delayed contacts PLd)
Safety data: IEC 61508 - High demand
Safety Integrity Level (SIL): 3 (for delayed contacts SIL2)
Safety data: IEC 61508 - Low demand
Safety Integrity Level (SIL): 3 (for delayed contacts SIL2)
Safety data: ENIEC 62061
Safety Integrity Level (SIL): 3 (for delayed contacts SIL2)
|
| Environmental and real-life conditions | Ambient conditions
Degree of protection: IP20
Min. degree of protection of inst. location: IP54
Ambient temperature (operation): -20°C ... 55°C (observe derating)
Ambient temperature (storage/transport): -40°C ... 70°C
Maximum altitude: ⤠2000 m (Above sea level)
Max. permissible humidity (storage/transport): 75 % (on average, 85% infrequently, non-condensing)
Max. permissible relative humidity (operation): 75 % (on average, 85% infrequently, non-condensing)
Shock: 15g
Vibration (operation): 10Hz...150Hz, 2g
|
| Approvals | CE
Certificate: CE-compliant
|
| Standards and regulations | Air clearances and creepage distances between the power circuits
Standards/regulations: DINEN50178/VDE0160
|
| Mounting | Mounting type: DIN rail mounting
Mounting position: any
Connection method: Push-in connection
|
Not available 
