Industrial Automation

Mechatronics

Industrial Safety

Panel Components

Sensors and Systems of Vision

Pneumatics

Network Comunications

Automation Cables

Design Software

Access services

Enter your reserved area

Access B2B
Log in to your account

Access services

Enter your reserved area

Access B2B
Log in to your account
Country|
||
PROSOFT TECHNOLOGY PS69-DPM
PROSOFT TECHNOLOGYNot available

PROFIBUS DPV1 PS69 Master Network Interface Module for CompactLogix

Product Code: PS69-DPM
Partner cod.: PS69-DPM
PROSOFT TECHNOLOGY


Diminuisci la quantità
Aumenta la quantità
Tecnichal data
Technical Specs
Description
Tecnichal data
Configuration
The configuration and diagnostic of the PROFIBUS system is done via the serial diagnostic interface of the module using the PROSOFT.fdt system configuration software tool. PROSOFT.fdt is FDT style configuration software and a communication DTM is included with the module allowing easy configuration of the PROFIBUS Master and network slave devices.
The master and network configuration are stored in the FLASH memory of the module.
The PS69-DPM interface appears to the Logix Controller as a standard I/O module and can be configured with RSLogix™ 5000 by Rockwell Automation®.
Specifications
Up to 32 PROFIBUS devices can be connected to one bus segment. If several bus segments are linked to each other with repeaters, there can be up to 127 devices on the network.
The maximum length of a bus segment depends on the baud rate used. Only PROFIBUS certified cable, preferably the cable type A, should be used.
Single Slot – 1769 backplane compatible
The module is recognized as an I/O module and the data exchange between controller and module is done via the I/O data image using CompactLogix / MicroLogix backplane technology.
Ladder logic is used for data transfer between module and processor. Sample ladder file included.
Supports CompactLogix processors and MicroLogix 1500 LRP
Technical Specs
Features and Benefits
PROFIBUS certified:Recognized quality certification mark
FDT configuration software and communication DTM included:Module DTM will configure master module and network slave devices. The DTM can be used in many FDT compatible software containers
Sample ladder program:Simplifies integration for quick and easy project start-up
Supports CIP ladder logic messaging:Request diagnostic, status and slave data based on ladder events. Offer better cyclic data performance
Specifications
Specification:Description
Slaves:Maximum 125
Input/Output:Maximum 244 Bytes per Slave
Input Data:Maximum 408 Bytes (*)
Acyclic Data:DPV1
Status data:88 Bytes
Output data:Maximum 480 Bytes (*)
Command data:16 Bytes
DPV1 services:Read / Write class 1, Alarm
Services:Global-Control, Slave-Diag, Set-Parameter
Sync, Freeze Command:Supported
Baud rate in kBit/s:Max. Distance
9.6:1,200 m / 4000 ft
19.2:1,200 m / 4000 ft
93.75:1,200 m / 4000 ft
187.5:1,000 m / 3280 ft
500:400 m / 1300 ft
1500:200 m / 650 ft
3000:100 m / 325 ft
6000:100 m / 325 ft
12000:100 m / 325 ft
Parameter:Value
Impedance:135 to 65 Ohm
Capacity:< 30 pF/m
Loop resistance:110 Ohm/km
Wire gauge:0.64 mm
Description
The PS69 PROFIBUS DP Master module expands the functionality of ’s CompactLogix / MicroLogix family of processors to include PROFIBUS. This module supports both I/O control and messaging, thus integrating DPV0 and DPV1 functionality into CompactLogix / MicroLogix. The PS69-DPM is a CompactLogix / MicroLogix compatible, PROFIBUS certified module, which enables controllers to communicate with a PROFIBUS network. The configuration and diagnostic of the PROFIBUS system is done via the serial diagnostic interface of the module using the System Configuration tool . The data exchange between controller and module is done via the I/O process data image using CompactLogix / MicroLogix backplane technology.