Not available 
| Notes | General Note: Assembling: Two 8 mm screws with 8 Nm on an isolated or grounded surface Long-wave surge current 2 ms in accordance with IEC 60099-4: 250 x 1.0 kA; 500 x 0.5 kA. |
| Product properties | IEC test classification: I / II T1 / T2 EN type: T1 / T2 IEC power supply system: TN-C IT Type: Installation module Product type: Arrester combination Product family: POWERTRAB Number of positions: 3 Surge protection fault message: Optical, remote indicator contact Insulation characteristics Overvoltage category: 8kV: IV (600V), III (1000V) Pollution degree: 3 |
| Electrical properties | Nominal frequency fN: 50 Hz (60Hz) Nominal voltage UN: 690 VAC Indicator/remote signaling Connection name: Remote fault indicator contact Switching function: 2x N/C contacts, 1-pos. Operating voltage: 30 VAC 30 VDC Operating current: 1.5 A AC 1.5 ADC Supply: Status indicator/remote signaling Operating voltage: 19.2 V AC/DC ... 30 V AC/DC Operating current: 7 mA AC/DC ... 13 mA AC/DC Rated current: 10 mA AC/DC Max. required back-up fuse: 1 A (e.g. T to IEC 127-2/III) Immunity to interference according to IEC 61000-4-5 (line-line): 1 kV Immunity to interference according to IEC 61000-4-5 (line-earth): 6 kV |
| Connection data | Double terminal point Connection method: Screw connection Screw thread: M6 Tightening torque: 8.5 Nm Stripping length: 24 mm Conductor cross section flexible: 16 mm² ... 50 mm² Conductor cross section rigid: 16 mm² ... 50 mm² Conductor cross section AWG: 6 ... 1/0 PE conductor connection Connection method: Ring cable lug Tightening torque: 20 Nm Conductor cross section flexible: 16 mm² ... 95 mm² Conductor cross section rigid: 16 mm² ... 95 mm² Conductor cross section AWG: 6 ... 3/0 Remote fault indicator contact Screw thread: M3 Tightening torque: 0.55 Nm Stripping length: 7 mm Conductor cross section flexible: 0.2 mm² ... 2.5 mm² Conductor cross section rigid: 0.2 mm² ... 2.5 mm² Conductor cross section AWG: 24 ... 12 |
| Dimensions | Dimensional drawing: https://dam-mdc.phoenixcontact.com/rendition/156443151564/d478abc62565034d8afb85e93927169f/-S204x204-FJPG Width: 176 mm Height: 191 mm Depth: 280 mm Horizontal pitch: 10 Div. |
| Material specifications | Color: Silver Flammability rating according to UL 94: V-2 CTI value of material: 600 250 Insulating material: PA/PC Material group: I (PA 6.6/PC) IIIa (PA 4.6) Housing surface material: die-cast aluminum Housing material: Die-cast aluminum, salt water resistant |
| Mechanical properties | Mechanical data Open side panel: No |
| Protective circuit | Mode of protection: L-PE Direction of action: 3L-PEN Nominal voltage UN: 690VAC 554/960VAC (TN-C) 690VAC (IT) Nominal frequency fN: 50 Hz (60Hz) Maximum continuous operating voltage UC (L-PE): 800 VAC Rated load current IL: 150 A (Serial through wiring with 50 mm²) Residual current IPE: ⤠20 µA Standby power consumption PC: ⤠48 mVA Nominal discharge current In (8/20) µs (L-PE): 35 kA Maximum discharge current Imax (8/20) µs (L-PE): 100 kA Impulse discharge current (10/350) µs (L-PE), charge: 17.5 As Impulse discharge current (10/350)µs (L-PE), specific energy: 305 kJ/é Impulse discharge current (10/350) µs (L-PE), peak current value Iimp: 35 kA Total discharge current Itotal (10/350)µs: 100 kA Follow current interrupt rating Ifi (L-PE): 50 kA Short-circuit current rating ISCCR: 50 kA Voltage protection level Up (L-PE): ⤠4.5 kV Residual voltage Ures (L-PE): ⤠2.7 kV (at In) ⤠2.5 kV (at 20 kA) ⤠2.3 kV (at 10 kA) ⤠2.2 kV (at 5 kA) ⤠2.1 kV (at 3kA) TOV behavior at UT (L-PE): 1960 VAC (200ms / withstand mode) 1500 VAC (5s / withstand mode) Response time tA (L-PE): ⤠100 ns Max. backup fuse with V-type through wiring: 125 A (gG at â¥35 mm²) Max. backup fuse with branch wiring: 400 A (gG at 2x 50 mm²) 800 A (aR (only up to Iimp = 25 kA)) |
| Environmental and real-life conditions | Ambient conditions Degree of protection: IP20 (only when all terminal points are used) Ambient temperature (operation): -40°C ... 80°C -40°C ... 55°C (serial through wiring â¥35mm²) Ambient temperature (storage/transport): -40°C ... 80°C Altitude: ⤠4000 m (amsl) Permissible humidity (operation): 5 % ... 95 % Shock (operation): 25g (Half-sine / 11 ms / 3x ±X, ±Y, ±Z) Vibration (operation): 5g (10 ... 150 Hz / 2.5 h / X, Y, Z) 4g (5 ... 100 Hz / X, Y, Z - according to GL ) |
| Approvals | UL specifications Maximum continuous operating voltage MCOV (L-L): 800 VAC Maximum continuous operating voltage MCOV (L-G): 800 VAC Nominal discharge current In (L-L): 20 kA Nominal discharge current In (L-G): 20 kA Mode of protection: L-L L-G Nominal voltage: 690VAC 400VAC Power distribution system: Wye Delta Nominal frequency: 60 Hz Measured limiting voltage MLV (L-L): 8750 V Measured limiting voltage MLV (L-G): 4370 V SPD Type: 4CA UL indicator/remote signaling Operating voltage: 30 VAC DC operating voltage: 30 VDC AC operating current: 1.5 A AC DC operating current: 1.5 ADC UL connection data Double terminal point Tightening torque: 75 lbf-in. Conductor cross section AWG: 1/0 ... 6 UL connection data PE conductor connection Tightening torque: 175 lbf-in. Conductor cross section AWG: 3/0 |
| Standards and regulations | Air clearances and creepage distances Standards/regulations: DINEN60664-1 / EN61643-11 Standards/specifications: IEC 61643-11 EN61643-11 Note: 2011 2012 |
| Mounting | Mounting type: Screw mounting |
| ECLASS | ECLASS-11.0: 27130802 ECLASS-13.0: 27171201 |
| ETIM | ETIM 9.0: EC000381 |
| UNSPSC | UNSPSC 21.0: 39121600 |
Description other products
