2903151 PHOENIX CONTACT - Technology Bsa

Input data	AC operation Network type: Star network Nominal input voltage range: 100 VAC ... 240 VAC Input voltage range: 100 VAC ... 240 VAC -15%...+10% Electric strength, max.: Ã¢¤ 300 VAC 15 s Typical national grid voltage: 120 VAC 230 VAC Voltage type of supply voltage: AC/DC Inrush current: Ã¢¤ 20 A (typical) Inrush current integral (I²t): < 0.9 A²s Inrush current limitation: typ. 20 A (after 1ms) AC frequency range: 50 Hz ... 60 Hz ±10% Mains buffering time: typ. 10 ms (120VAC) typ. 15 ms (230 V AC) Current consumption: 5.6 A (100VAC) 4.3 A (120VAC) 2.4 A (230 V AC) 2.4 A (240VAC) Nominal power consumption: 534.7 VA Protective circuit: Transient surge protection; Varistor Power factor (cos phi): 0.98 Typical response time: < 1 s Input fuse: 10 A (internal (device protection)) Recommended breaker for input protection: 10 A ... 16 A (Characteristics B, C, D, K) Discharge current to PE: < 3.5 mA POWER factor: > 0.9 (120VAC) > 0.9 (230 V AC) DC operation Nominal input voltage range: 110 VDC ... 250 VDC Input voltage range: 110 VDC ... 250 VDC ±10% Extended input voltage range in operation: > 99 VDC Switch-on voltage: Ã¢¥ 96 VDC Shut-down voltage: < 95 VDC Mains buffering time: > 15 ms (230 V AC) Current consumption: 4.9 A (110VDC) 2.1 A (250VDC)
Output data	Efficiency: typ. 91.4 % (120VAC) typ. 92.9 % (230 V AC) Output characteristic: U/I with dynamic load reserve Nominal output voltage: 24 VDC ±1% Setting range of the output voltage (U_Set): 24 VDC ... 28 VDC (> 24 VDC, constant capacity restricted) Nominal output current (I_N): 20 A Dynamic Boost (I_Dyn.Boost): 30 A (5 s) Derating: > 60°C ... 70°C (2.5%/K) POWER factor: > 0.9 (120VAC) > 0.9 (230 V AC) Feedback voltage resistance: Ã¢¤ 35 VDC Protection against overvoltage at the output (OVP): Ã¢¤ 30 VDC Control deviation: < 1 % (change in load, static 10 % ... 90 %) < 3 % (Dynamic load change 10 % ... 90 %, 10 Hz) < 0.1 % (change in input voltage ±10 %) Residual ripple: < 100 mV_PP (with nominal values) Short-circuit-proof: yes No-load proof: yes Output power: 480 W 720 W Maximum no-load power dissipation: < 2.9 W (120VAC) < 2.8 W (230 V AC) Power loss nominal load max.: < 44.8 W (120VAC) < 36.8 W (230 V AC) Rise time: 20 ms (U_OUT (10 % ... 90 %)) Connection in parallel: yes, for redundancy and increased capacity Connection in series: yes Signal: DC OK Continuous load current: 100 mA Signal relay 13/14 Default: closed Digital: 30 VAC 30 VDC 100 mA
Connection data	Input Connection method: Push-in connection Conductor cross section, rigid min.: 0.2 mm² Conductor cross section, rigid max.: 4 mm² Conductor cross section flexible min.: 0.2 mm² Conductor cross section flexible max.: 2.5 mm² Single conductor/terminal point, stranded, with ferrule, min.: 0.2 mm² Single conductor/terminal point, stranded, with ferrule, max.: 2.5 mm² Conductor cross section AWG min.: 24 Conductor cross section AWG max.: 12 Stripping length: 10 mm Output Connection method: Push-in connection Conductor cross section, rigid min.: 0.2 mm² Conductor cross section, rigid max.: 10 mm² Conductor cross section flexible min.: 0.2 mm² Conductor cross section flexible max.: 6 mm² Single conductor/terminal point, stranded, with ferrule, min.: 0.2 mm² Single conductor/terminal point, stranded, with ferrule, max.: 6 mm² Conductor cross section AWG min.: 24 Conductor cross section AWG max.: 8 Stripping length: 15 mm Signal Connection method: Push-in connection Conductor cross section, rigid min.: 0.2 mm² Conductor cross section, rigid max.: 1.5 mm² Conductor cross section flexible min.: 0.2 mm² Conductor cross section flexible max.: 1.5 mm² Single conductor/terminal point, stranded, with ferrule, min.: 0.2 mm² Single conductor/terminal point, stranded, with ferrule, max.: 1.5 mm² Conductor cross section AWG min.: 24 Conductor cross section AWG max.: 16 Stripping length: 8 mm
Signaling	Types of signaling: LED Floating signal contact Signal output: LED status indicator Signalization designation: DC OK Status display: LED Color: green DC OK: U_OUT > 0.9 x U_N (U_N = 24VDC)
Electrical properties	Number of phases: 1.00 Insulation voltage input/output: 3 kV AC (type test) 1.5 kV AC (routine test)
Product properties	Product type: Power supply Product family: TRIO POWER MTBF (IEC 61709, SN 29500): > 1800000 h (25°C) > 1000000 h (40°C) > 480000 h (60°C) Insulation characteristics Protection class: I (in closed control cabinet) Degree of pollution: 2
Dimensions	Width: 68 mm Height: 130 mm Depth: 160 mm Installation dimensions Installation distance right/left: 0 mm / 0 mm Installation distance top/bottom: 50 mm / 50 mm
Mounting	Mounting type: DIN rail mounting Assembly instructions: alignable: horizontally 0 mm (Ã¢¤ 40°C) 10 mm (Ã¢¤ 70°C), vertically 50 mm Mounting position: horizontal DIN rail NS 35, EN 60715 With protective coating: No
Material specifications	Flammability rating according to UL94 (housing / terminal blocks): V0 Housing material: Metal Type of housing: Aluminum (AlMg3) Hood version: Polycarbonate
Environmental and real-life conditions	Ambient conditions Degree of protection: IP20 Ambient temperature (operation): -25°C ... 70°C (>60°C Derating: 2,5%/K) Ambient temperature (storage/transport): -40°C ... 85°C Ambient temperature (start-up type tested): -40°C Maximum altitude: Ã¢¤ 4000 m (>2000m, Derating: 10%/1000m) Climatic class: 3K3 (in acc. with EN 60721) Max. permissible relative humidity (operation): Ã¢¤ 95 % (at 25°C, non-condensing) Shock: 18 ms, 30g, in each space direction (according to IEC 60068-2-27) Vibration (operation): < 15 Hz, amplitude ±2.5 mm (according to IEC 60068-2-6) 15 Hz ... 150 Hz, 4g, 90 min.
Standards and regulations	Rail applications: EN50121-4 Standard Ã¢ Electronic equipment for use in electrical power installations and their assembly into electrical power installations: EN50178/VDE0160 (PELV) Standard Ã¢ Limitation of mains harmonic currents: EN61000-3-2 Standard - Electrical safety: IEC 60950-1/VDE0805 (SELV) Standard Ã¢ Safety extra-low voltage: IEC 60950-1 (SELV) and EN60204-1 (PELV) Standard - Safe isolation: DINVDE0100-410 Standard - Safety of transformers: EN61558-2-16 (air clearances and creepage distances only)
Approvals	Shipbuilding approval: DNV GL UL approvals: UL Listed UL508 UL/C-UL Recognized UL60950-1 UL ANSI/ISA-12.12.01 Class I, Division 2, Groups A, B, C, D (Hazardous Location) Conformity/Approvals SIL in accordance with IEC 61508: 0
EMC data	Low Voltage Directive: Conformance with Low Voltage Directive 2014/35/EC EMC requirements for noise emission: EN61000-6-3 EN61000-6-4 EMC requirements for noise immunity: EN61000-6-1 EN61000-6-2 Electromagnetic compatibility: Conformance with EMC Directive 2014/30/EU Conducted noise emission: EN55016 EN61000-6-3 (Class B) Noise emission: EN 55011 (EN 55022) EN55016 EN61000-6-3 (Class B) Harmonic currents Frequency range: Class A, B Flicker Frequency range: 0 kHz ... 2 kHz Electrostatic discharge Standards/regulations: EN61000-4-2 Electrostatic dischargeÃ¢ Contact discharge: 6 kV (Test Level 4) Discharge in air: 8 kV (Test Level 4) Comments: Criterion A Electromagnetic HF field Standards/regulations: EN61000-4-3 Electromagnetic HF fieldÃ¢ Frequency range: 80 MHz ... 1 GHz 1 GHz ... 2 GHz 2 GHz ... 3 GHz Test field strength: 10 V/m (Test Level 3) Comments: Criterion A Fast transients (burst) Standards/regulations: EN61000-4-4 Fast transients (burst)Ã¢ Input: 4 kV (Test Level 4 - asymmetrical) Output: 2 kV (Test Level 3 - asymmetrical) Signal: 1 kV (Test Level 2 - asymmetrical) Comments: Criterion A Surge voltage load (surge) Standards/regulations: EN61000-4-5 Input: 3 kV (Test Level 3 - symmetrical) 6 kV (Test Level 4 - asymmetrical) Output: 1 kV (Test Level 2 - symmetrical) 2 kV (Test Level 1 - asymmetrical) Signal: 1 kV (Test Level 2 - asymmetrical) Comments: Criterion B Conducted interference Standards/regulations: EN61000-4-6 Conducted interferenceÃ¢ Input/Output: asymmetrical Frequency range: 0.15 MHz ... 80 MHz Comments: Criterion A Voltage: 10 V (Test Level 3) Emitted interference Standards/regulations: EN61000-6-3 Radio interference voltage in acc. with EN 55011: EN55011 (EN55022) ClassB, area of application: Industry and residential Emitted radio interference in acc. with EN 55011: EN 55011 (EN 55022) Class B, area of application: Industry and residential Criteria Criterion A: Normal operating behavior within the specified limits. Criterion B: Temporary impairment to operational behavior that is corrected by the device itself.