2905577 PHOENIX CONTACT - Technology Bsa

MINI MCR-SL-IDS-I-I - Output signal conditioner

3-way output signal conditioner for transmitting 0/4 ... 20 mA signals from the controller to a load located in the field with simultaneous 3-way electrical isolation between the input, output, and supply, with screw connection

Product Code: 2905577

Partner cod.: 2905577

PHOENIX CONTACT

Notes	Utilization restriction EMC note: EMC: class A product, see manufacturer's declaration in the download area
Product properties	Product type: Repeater power supplies Product family: MINI Analog No. of channels: 1 Insulation characteristics Overvoltage category: II Pollution degree: 2
Electrical properties	No. of channels: 1 Electrical isolation: 3-way isolation Limit frequency (3 dB): > 175 Hz Protective circuit: Transient protection Signal transmission behavior: In=Out Step response (10-90%): < 2 ms Maximum temperature coefficient: < 0.01 %/K Temperature coefficient, typical: < 0.01 %/K Maximum transmission error: Ã¢¤ 0.1 % (of final value) Electrical isolation Input/output/power supply Rated insulation voltage: 50 V AC/DC Test voltage: 1.5 kV AC (50Hz, 60s) Insulation: Basic insulation in accordance with IEC/EN61010 Supply Nominal supply voltage: 24 VDC Supply voltage range: 19.2 VDC ... 30 VDC (The DIN rail connector (ME 6,2 TBUS-2 1,5/5-ST-3,81 GN, item no. 2869728) can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail in accordance with EN60715) Power consumption: < 600 mW (at 24 V DC)
Input data	Signal Number of inputs: 1 Current input signal: 0 mA ... 20 mA 4 mA ... 20 mA Max. current input signal: 20 mA Input voltage limitation: < 2 V (20mA)
Output data	Signal: Current Number of outputs: 1 Current output signal: 0 mA ... 20 mA 4 mA ... 20 mA Load/output load current output: Ã¢¤ 800 Ã© (at 20 mA) Ripple: < 20 mV_rms
Connection data	Connection method: Screw connection Stripping length: 12 mm Screw thread: M3 Conductor cross section rigid: 0.2 mm² ... 2.5 mm² Conductor cross section flexible: 0.2 mm² ... 2.5 mm² Conductor cross section AWG: 26 ... 12
Interfaces	Data communication (bypass) HART function: Yes Limit frequency (3 dB): 2.5 Hz
Dimensions	Dimensional drawing: https://dam-mdc.phoenixcontact.com/rendition/156443151564/8450693c9d67004aa7841c306225c8da/-S204x204-FJPG Width: 6.2 mm Height: 93.1 mm Depth: 101.2 mm
Material specifications	Fire protection for rail vehicles (DIN EN 45545-2) R22: HL 1 - HL 2 Fire protection for rail vehicles (DIN EN 45545-2) R23: HL 1 - HL 2 Fire protection for rail vehicles (DIN EN 45545-2) R24: HL 1 - HL 2 Housing material: PBT
Environmental and real-life conditions	Ambient conditions Degree of protection: IP20 Ambient temperature (operation): -20°C ... 60°C Ambient temperature (storage/transport): -40°C ... 85°C Altitude: Ã¢¤ 2000 m Permissible humidity (operation): 5 % ... 95 % (non-condensing)
Approvals	CE Certificate: CE-compliant UKCA Certificate: UKCA-compliant UL, USA/Canada Identification: UL508 Listed Class I, Div. 2, Groups A, B, C, D T4 Class I, Zone 2, Group IIC Shipbuilding approval Certificate: DNV GL TAA000020N DNV GL data Temperature: B Humidity: B Vibration: B EMC: A Enclosure: Required protection according to the Rules shall be provided upon installation on board
EMC data	Noise immunity: EN 61000-6-2 Note: When being exposed to interference, there may be minimal deviations. Electromagnetic compatibility: Conformance with EMC directive Noise emission: EN 61000-6-4 Electrostatic discharge Standards/regulations: EN61000-4-2 Electrostatic dischargeÃ¢ Comments: Safety measures must be taken to prevent electrostatic discharge. Electromagnetic HF field Designation: Electromagnetic RF field Standards/regulations: EN61000-4-3 Typical deviation from the measuring range final value: 3 % Fast transients (burst) Designation: Fast transients (burst) Standards/regulations: EN61000-4-4 Typical deviation from the measuring range final value: 3 % Surge current load (surge) Standards/regulations: EN61000-4-5 Surge current load (surge)Ã¢ Comments: Criterion B Conducted interference Designation: Conducted interferences Standards/regulations: EN61000-4-6 Typical deviation from the measuring range final value: 3 %
Standards and regulations	Electrical isolation: 3-way isolation
Mounting	Mounting type: DIN rail mounting Assembly instructions: The DIN rail connector (ME 6,2 TBUS-2 1,5/5-ST-3,81 GN, item no. 2869728) can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail in accordance with EN 60715. Mounting position: any